Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
Revision 1.41 (02-23-12)
PRODUCT PREVIEW
2
SMSC EMC1413 / EMC1414
Multiple Channel 1°C Temperature Sensors with Beta Compensation
Block Diagram
V
DD
EMC1413/ EMC1414
*
EMC1414 only
Conversion Rate Register
Switching
Current
Low Limit Registers
Limit Comparator
Analog
Mux
ΔΣ
ADC
External Temperature
Register(s)
SMCLK
SMBus Interface
High Limit Registers
Digital Mux
THERM Limit Register
Digital Mux
SMDATA
DP1
DN1
DP2 / DN3
*
DN2 / DP3
*
Anti-parallel
Diodes
Internal Temp
Diode
ALERT
THERM Hysteresis Register
Internal
Temperature Register
Interupt Masking
Configuration Register
THERM / ADDR
SMBus Address Decode
GND
Status Registers
Figure 1 EMC1414 Block Diagram
SMSC EMC1413 / EMC1414
PRODUCT PREVIEW
3
Revision 1.41 (02-23-12)
Multiple Channel 1°C Temperature Sensors with Beta Compensation
Package Outlines
REVISION HISTORY
3
5
REVISION
A
DESCRIPTION
INITIAL RELEASE
DATE
3/29/05
RELEASED BY
S.K.ILIEV
D
e
PIN 1 IDENTIFIER
AREA (D/2 X E1/2)
c
4
3
E1
E
4
2
10X b
SEE DETAIL "A"
TOP VIEW
END VIEW
A2
C
A
SEATING PLANE
A1
ccc C
SIDE VIEW
3-D VIEW
H
C
0.25
SEATING PLANE
GAUGE PLANE
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETER.
2. TOLERANCE ON THE TRUE POSITION OF EACH LEAD IS ± 0.04 mm AT MAXIMUM MATERIAL
CONDITION.
3. PACKAGE BODY DIMENSIONS "D" AND "E1" DO NOT INCLUDE MOLD/INTERLEAD PROTRUSIONS
OR FLASH. MAXIMUM MOLD PROTRUSIONS OR FLASH IS 0.15 mm (0.006 INCHES) PER END AND
SIDE. DIMENSIONS "D" AND "E1" ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE
PLASTIC BODY, INCLUDING ANY MISMATCH BETWEEN TOP AND BOTTOM PLASTIC BODY. THEY
ARE DETERMINED AT DATUM PLANE "H".
4. DIMENSIONS "b" AND "c" APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.08 mm AND
0.15 mm FROM THE LEAD TIP.
5. DETAILS OF THE PIN 1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE
INDICATED.
0° - 8°
L
(0.95)
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
AND TOLERANCES ARE:
DECIMAL
±0.1
X.X
X.XX ±0.05
X.XXX ±0.025
ANGULAR
±1°
THIRD ANGLE PROJECTION
80 ARKAY DRIVE
HAUPPAUGE, NY 11788
USA
TITLE
DETAIL "A"
DIM AND TOL PER ASME Y14.5M - 1994
MATERIAL
NAME
DRAWN
DATE
-
-
S.K.ILIEV
CHECKED
3/29/05
3/29/05
SCALE
PACKAGE OUTLINE
10 PIN TSSOP, 3x3 MM BODY, 0.50 MM PITCH
DWG NUMBER
FINISH
S.K.ILIEV
APPROVED
MO-10-TSSOP-3x3
STD COMPLIANCE
SHEET
REV
A
1 OF 1
PRINT WITH "SCALE TO FIT"
DO NOT SCALE DRAWING
S.K.ILIEV
3/29/05
1:1
JEDEC: MO-187
Figure 2 10-Pin MSOP / TSSOP Package
Revision 1.41 (02-23-12)
PRODUCT PREVIEW
4
SMSC EMC1413 / EMC1414
Multiple Channel 1°C Temperature Sensors with Beta Compensation
京公网安备 11010802033920号
EEWORLD
