Z – LEAD SURFACE MOUNT SPECIFICATION
AC AXIAL CEMENTED WIREWOUND RESISTOR
& PR POWER METAL FILM RESISTORS
FEATURES
•
Surface mounted version
•
Low cost alternative for SMD molded resistor
•
High power dissipation in small volume
•
High pulse load handling capabilities
•
High temperature silicone coating
TECHNOLOGY
Wire wound resistor AC03 / AC05
The resistor element is a resistive wire, which is wound, in a single layer on a ceramic rod. Metal caps are
pressed over the ends of the rod. The ends of the resistance wire and tinned copper-clad leads are
connected to the caps by welding. The resistor is coated with green silicon cement which is non-flammable,
will not drip even at high overloads and is resistant to most commonly used cleaning solvents, in accordance
with “MIL-STD-202E, method 215” and “IEC 60068-2-45”.
Metal film power resistor PR03
A homogenous film of metal alloy is deposited on a high-grade ceramic core. The leads are welded on this
caps and a helical groove has been cut in the resistive layer. The resistor is coated with red silicon cement
which is non-flammable, will not drip even at high overloads and is resistant to most commonly used
cleaning solvents, providing electrical, mechanical and climatic protection.
©
PHOENIX DO BRASIL LTDA
AC PR Z LEAD
Preliminary Specification
Revision
July 28 2005
Page
1
of
9
All rights are reserved. Reproduction whole or in part is
prohibited without the written consent of the copyright owner.
QUICK REFERENCE DATA
DESCRIPTION
Resistance range
( 1
)
PR03
0.33
Ω
- 1 MΩ
±5%,
E24
1
Ω
- 1 MΩ
±1%,
E24/E96
3W
750 V
AC03
0.1
Ω
- 5.1 kΩ
AC05
0.1
Ω
- 8.2 kΩ
Tolerance and series
Maximum dissipation at
T
amb
= 25°
C
Limiting voltage (DC or RMS)
Rated voltage
(
2 )
3 )
±5%
and
±1%,
E24/E96
3W
-
Pn x R
5W
-
Temperature coefficient
(
Basic specification
±250
ppm/°
C
IEC 60115-1 and 60115-4
55/155/56
R
R < 10
Ω:
0 to 600 ppm/°
C
10
Ω:
- 80 to + 140 ppm/°
(2)
C
IEC60 115-1
40/200/56
Climatic category (IEC 60068)
Stability
∆R/R
max
after:
Load
Climatic tests
Resistance to soldering heat
±5%
+ 0.1
Ω
±3%
+ 0.1
Ω
±1%
+ 0.05
Ω
±1%
+ 0.1
Ω
±1%
+ 0.1
Ω
±0.5%
+ 0.05
Ω
±5% + 0.1
Ω
±1% + 0.05
Ω
±0.5% + 0.05
Ω
±5% + 0.1
Ω
±1% + 0.05
Ω
±0.5% + 0.05
Ω
(1)
(2)
(3)
Special resistive values available on request
Maximum rated voltage is the limiting voltage
Temperature coefficient 30, 50 and 90 ppm/° available on request
C
©
PHOENIX DO BRASIL LTDA
AC PR Z LEAD
Preliminary Specification
Revision
July 28 2005
Page
2
of
9
All rights are reserved. Reproduction whole or in part is
prohibited without the written consent of the copyright owner.
MECHANICAL DATA
Standard pad sizes
Table 1.
TYPE
L max
∅
D max
∅
d
P
±
1
(± 0.039)
±
21.0
(0.827)
16.5
(0.649)
21.0
(0.827)
(1)
h max
(1) (2)
W max
(1)
A min
(1)
B max
(1)
C min
E min
PR03
16.5
(0.650)
12.5
(0.492)
17.0
(0.669)
5.2
(0.205)
5.5
(0.22)
7.5
(0.295)
0.8 FeCu
(0.031)
0.8 FeCu
(0.031)
0.8 FeCu
(0.031)
5.0
(0.197)
5.0
(0.197)
5.0
(0.197)
7.5
(0.295)
7.5
(0.295)
7.5
(0.295)
24.5
(0.965)
20.0
(0.787)
24.5
(0.965)
17.5
(0.689)
13.0
(0.512)
17.5
(0.689)
3.5
(0.138)
3.5
(0.138)
3.5
(0.138)
8.0
(0.315)
8.0
(0.315)
8.0
(0.315)
AC03
AC05
Dimensions in mm (inches)
(1) Other dimensions available under request
(2) Dimensions to be confirmed
©
PHOENIX DO BRASIL LTDA
AC PR Z LEAD
Preliminary Specification
Revision
July 28 2005
Page
3
of
9
All rights are reserved. Reproduction whole or in part is
prohibited without the written consent of the copyright owner.
ELECTRICAL CHARACTERISTICS
DERATING: AC03 AND AC05
120
P
max
(%)
100
80
60
40
20
0
0
25
50
75
100
125
150
175
200
T
amb
(°
C)
Maximum dissipation (P
max
) in percentage of rated power as a function of ambient temperature (T
amb
)
DERATING: PR03
120
P
max
(%)
100
80
60
40
20
0
0
25
50
75
100
125
150
175
T
amb
(°
C)
Maximum dissipation (P
max
) in percentage of rated power as a function of ambient temperature (T
amb
)
©
PHOENIX DO BRASIL LTDA
AC PR Z LEAD
Preliminary Specification
Revision
July 28 2005
Page
4
of
9
All rights are reserved. Reproduction whole or in part is
prohibited without the written consent of the copyright owner.
MARKING
WIRE WOUND RESISTOR
The resistor is marked with the nominal resistance value, the tolerance on the resistance and the rated
dissipation at T
amb
= 25 ºC.
For values up to 910
Ω,
the R is used as the decimal point.
For values of 1 KΩ and upwards, the letter K is used as the decimal point for the KΩ indication.
Example:
6K8 5%
5W
FILM RESISTOR
The nominal resistance and tolerance are marked on the resistor using four or five colored bands in
accordance with IEC publication 60062 “color code for fixed resistors”.
Standard values of nominal resistance are taken from the E24/E96 series for resistors with a tolerance of
±5% or 1%. The values of the E24/E96 series are in accordance with “IEC publication 60063”.
ORDERING INFORMATION
Table 2. Ordering code.
TYPE
LEAD
∅
TOLERANCE
QUANTITY
(pcs)
PACKAGING
ORDERING
CODE
PR03
±
1%
±
5%
200
Under request
2306 199 55xxx
AC03
0.80 FeCu
(0.031)
±
1%
±
5%
±
1%
±
5%
200
IN BOX
Under request
2306 326 55xxx
AC05
200
Under request
2306 321 55xxx
Dimensions unless specified in mm (inches)
The resistors have a 12 digit ordering code starting with 2306.
The subsequent 6 or 7 digits indicate the resistor type and packaging see table 2.
For 5% tolerance the remaining 3 digits indicate the resistance value;
- The first 2 digits indicate the resistance value.
- The last digit indicates the resistance decade in accordance with table 3.
For 1% tolerance the remaining 4 digits indicate the resistance value;
- The first 3 digits indicate the resistance value.
- The last digit indicates the resistance decade in accordance with table 3.
©
PHOENIX DO BRASIL LTDA
AC PR Z LEAD
Preliminary Specification
Revision
July 28 2005
Page
5
of
9
All rights are reserved. Reproduction whole or in part is
prohibited without the written consent of the copyright owner.
京公网安备 11010802033920号
EEWORLD
