Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-1LD 2.5 GHz
DWDM Wideband Fiber Optic Link
DATASHEET | MAY 2016
SATCOM
Performance Highlights
5
Parameter
Link
1
Frequency Range
50 Ohm
75 Ohm
Frequency Response
Any 36 MHz
50-2500 MHz
Noise Figure (TG max, RG max, 1.5 GHz)
Input IP3 (TG max, 1.5 GHz)
Spur Free Dynamic Range
6
RF Link Gain (TG max, RG max)
3
Standard Rx (OTS-1LR)
Hi-Sensitivity Rx (OTS-1LSR)
Tx
RF Input within Smart Gain Control (SGC) range
2
RF Input without SGC
Tx Gain (TG) max, 1.5 GHz
TG Adjustment Range (from max)
Optical Output
Wavelength (ITU-DWDM)
Input Return Loss
50-2500 MHz
LNB Voltage
Current
DC Power
LNB Off
Rx
Optical Input
Standard Rx (OTS-1LR)
Hi-Sensitivity Rx (OTS-1LSR)
Rx Gain (RG) max, 1.5 GHz
Standard Rx (OTS-1LR)
Hi-Sensitivity Rx (OTS-1LSR)
RG Adjustment Range (from max)
Output IP3 (5 dBmo to Rx, 0 dBm 2150 MHz)
RF Output (-35 dBm input, TG max, 1 dBmo to Rx)
Standard Rx
High Sensitivity Rx
Output Return Loss
50-2700 MHz (50 Ohm), 50-2500 MHz (75 Ohm)
DC Power
1. For link over 1 m fiber
2. Wider RF inputs are acceptable, but will set the RF amp gain to its limit
3. Link RF Gain
dB
= TG + RG – 2 * Fiber Loss
dBo
(assumes Rin = Rout)
4. Minimum optical input to maintain 35 dB C/N on 36 MHz RF carrier over 1 m fiber
5. Performance at ambient temperature (unless specified otherwise)
6. SFDR = 2/3 * (IIP3 + 174 - NF)
7. Some specifications in the table may degrade when operating at low input
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
Optiva OTS-1LD 2.5 GHz
DWDM Wideband Fiber Optic Link
DATASHEET | MAY 2016
SATCOM
Laser Safety
This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser
product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are
Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser prod-
ucts. For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example:
eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warn-
ing shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and
binoculars) may pose an eye hazard.
Wavelength = 1.3/1.5 μm.
Maximum power = 30 mW.
INVISIBLE LASER RADIATION
AVOID DIRECT EXPOSURE
TO BEAM
INVISIBLE LASER RADIATION IS
EMITTED FROM THE END OF
FIBER OR CONNECTOR
Wavelength: 1.5 µm
Max. Output: 50 mW
Class 1M Laser Product
Avoid direct exposure to beam
Do not view beam directly with
optical instruments
INVISIBLE LASER RADIATION EMITTED FROM END OF FIBER OR CONNECTOR
CLASS 1M LASER PRODUCT IEC 60825-1:2007 EN 60825-1:2007
MAX OUTPUT: 50 mW WAVELENGTH: 1.5 µm (+ 1460 to 1620 nm)
Complies with 21 CRF 1040.10 and 1040.11 except for deviations pursuant
to Laser Notice No. 50, dated June 24, 2007
G8760-073-001 REV.3
*Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
*IEC is a registered trademark of the International Electrotechnical Commision.
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
京公网安备 11010802033920号
EEWORLD
