EEWORLDEEWORLDEEWORLD

Part Number

Search

ISM92-1254FH-1.500

Description
Oscillator
CategoryPassive components    oscillator   
File Size94KB,1 Pages
ManufacturerILSI
Websitehttp://www.ilsiamerica.com
Environmental Compliance
Download Datasheet Parametric View All

ISM92-1254FH-1.500 Overview

Oscillator

ISM92-1254FH-1.500 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7355499031
Reach Compliance Codecompliant
YTEOL0
Other featuresTRI-STATE; ENABLE/DISABLE FUNCTION; TR
Frequency Adjustment - MechanicalNO
frequency stability20%
Installation featuresSURFACE MOUNT
Number of terminals4
Nominal operating frequency1.5 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeACMOS
physical size5.0mm x 3.2mm x 1.3mm
Maximum supply voltage1.89 V
Minimum supply voltage1.71 V
Nominal supply voltage1.8 V
surface mountYES
maximum symmetry45/55 %
SMD Oscillator, TTL / HC-MOS
Ceramic Package, 3.2 mm x 5 mm
Frequency
Output Level
Level
Duty Cycle
Rise / Fall Time
Output Load
Frequency Stability
Start-up Time
Enable / Disable Time
Jitter
Supply Voltage
Current
Temperature
Operating
Storage
Environmental / Tape and Reel
Package Information
1.500 MHz to 80.000 MHz
ISM92 Series
TTL
HC-MOS
‘0’= 0.4 VDC Max., ‘1’ = 2.4 VDC Min.
‘0’ = 0.1 Vcc Max., ‘1’= 0.9 Vcc Min.
Specify 50%
±
10% or
±
5% See Table
5 nS Max. @ Vcc = +3.3 VDC, 10 nS Max. @ Vcc = +5 VDC **
Fo < 50 MHz = 10 TTL, Fo > 50 MHz = 5 LSTTL
See Table
See Frequency Stability Table
(Includes room temperature tolerance and stability over operating temperature)
10 mS Max.
100 nS Max.
1 MHz to 75 MHz - 5 pS RMS (1 sigma) Max. accumulated jitter (20K adjacent periods), 1.5 pS RMS (1 sigma) Max.
integrated jitter (12KHz to 20MHz), 50 pS p-p Max. total jitter (100K adjacent periods)
76 MHz to 150 MHz - 3 pS RMS (1 sigma) Max. accumulated jitter (20K adjacent periods), 1 pS RMS (1 sigma) Max.
integrated jitter (12KHz to 20MHz), 30 pS p-p Max. total jitter (100K adjacent periods)
See Input Voltage Table, tolerance
±5
%
40 mA Max. ***
See Operating Temperature Table
-55° C to +125° C
See Appendix B for Environmental information, Appendix C for Tape and Reel information
MSL = N.A., Termination = e4
Tri-State Function
Pin 1 Open
Enable
Pin 1
70% Vdd
Enable
Pin 1
30% Vdd
Disable
Part Number Guide
Package
Input
Voltage
5 = 5.0 V
3 = 3.3 V
7 = 3.0 V
2 = 2.7 V
6 = 2.5 V
1 = 1.8 V*
Sample Part Number:
Operating
Temperature
1 = 0° C to +70° C
6 = -10° C to +70° C
3 = -20° C to +70° C
4 = -30° C to +75° C
2 = -40° C to +85° C
Symmetry
(Duty Cycle)
5 = 45 / 55 Max.
6 = 40 / 60 Max.
ISM92 - 3251BH - 20.000
Output
1 = 10TTL / 15 pF HC-MOS
3 = 15 pF HC-MOS
6 = 30 pF
5 = 50 pF HC-MOS (<40 MHz)
4 = AC-MOS
Stability
(in ppm)
**D =
±15
**F =
±20
A =
±25
B =
±50
C =
±100
- 20.000 MHz
Enable /
Disable
H = Enable
Frequency
ISM92 -
NOTE: A 0.01 µF bypass capacitor is recommended between Vcc (pin 4) and Gnd (pin 2) to minimize power supply noise.
** Not available for all temperature ranges. ** Frequency, supply, and load related parameters.
5/08 Rev A
ILSI America
Phone: 775-851-8880 • Fax: 775-851-8882• e-mail: e-mail@ilsiamerica.com • www.ilsiamerica.com
Specifications subject to change without notice
Say goodbye to quartz? One of the main characters in next week's TI live broadcast, CC2652RB, is a wireless MCU that does not require an external crystal oscillator
[size=2]Next Tuesday, TI will introduce its latest SimpleLink wireless MCU products: CC13X2 and CC26X2 at the forum. The highlights are low power consumption and multi-band. The official publicity of ...
nmg Wireless Connectivity
How to calculate the input impedance of this full-bridge rectifier?
The green box is equivalent to VEQ, and the rest of the rectifier and BUCK circuit is equivalent to this Rload. So how do I calculate this Rload? The switch signal parameters are shown in Figure 1....
fishiscat Analogue and Mixed Signal
Design of receiving circuit for radio remote control transmitter
Although OOK modulation has poor performance, its circuit is simple, easy to implement, and stable in operation. Therefore, it has been widely used. Such circuits are almost always used in car and mot...
Aguilera Wireless Connectivity
【Portable Environmental Status Detector】Use of GPIO port
When it comes to a new development board, the GPIO port is the best starting point, and the ESP32-S2-Kaluga-1 kit is no exception. A basic example provided in the routine is to light up the WS2812, bu...
jinglixixi DigiKey Technology Zone
How to Layout a Circuit Board for an Op Amp
During the circuit design process, application engineers often overlook the layout of the printed circuit board (PCB). The problem often encountered is that the circuit schematic is correct, but it do...
ohahaha PCB Design
Research on Charging Method of Lead-acid Battery
[i=s]This post was last edited by qwqwqw2088 on 2021-7-26 08:06[/i]Lead-acid batteries have been widely used due to their low manufacturing cost, large capacity and low price. However, if used imprope...
qwqwqw2088 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号