EEWORLDEEWORLDEEWORLD

Part Number

Search

H1505CA2293DHW-W

Description
Fixed Resistor, Thin Film, 0.35W, 229000ohm, 125V, 0.5% +/-Tol, -50,50ppm/Cel, 1505,
CategoryPassive components    The resistor   
File Size100KB,1 Pages
ManufacturerState of the Art Inc.
Environmental Compliance
Download Datasheet Parametric View All

H1505CA2293DHW-W Overview

Fixed Resistor, Thin Film, 0.35W, 229000ohm, 125V, 0.5% +/-Tol, -50,50ppm/Cel, 1505,

H1505CA2293DHW-W Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid930843176
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.37
structureChip
JESD-609 codee4
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.38 mm
Package length3.85 mm
Package formSMT
Package width1.22 mm
method of packingWaffle Pack
Rated power dissipation(P)0.35 W
resistance229000 Ω
Resistor typeFIXED RESISTOR
series1505(STD)-THINFILM
size code1505
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceGold (Au)
Tolerance0.5%
Operating Voltage125 V

H1505CA2293DHW-W Preview

PROTECTIVE
ENCAPSULANT
1505 Thin Film Chip Resistor
Standard Grade, Wraparound
PERFORMANCE CHARACTERISTICS
Resistance Range(1)
Tolerances (2)
TCR
Thermal Resistance
Maximum Power
Maximum Voltage
5.6
W- 1MW
0.1%, 0.25%, 0.5%,1%, 2%, 5%
±25, ±50, ±100 ppm
100.5°C/W
350 mW
125 Volts
WRAPAROUND
TERMINATIONS
PRECISION
THIN FILM
99.6% ALUMINA
CURRENT NOISE
TEMPERATURE RISE (°C)
POWER DISSIPATION
fiber epoxy board
(1) Minimum resistance range at 0.1% tolerance is 100ohms.
(2) +/- 0.05% limited availability - consult factory
ceramic board
ENVIRONMENTAL PERFORMANCE (3)
Thermal Shock
Low Temperature Operation
Short-time Overload
Resistance to Bonding Exposure
Moisture Resistance
High Temperature Exposure
Life Test
±0.02%
±0.02%
±0.02%
±0.02%
±0.03%
±0.03%
See Chart
POWER DISSIPATION (WATTS)
TYPICAL LIFE TEST PERFORMANCE
POWER DERATING
(3)Typical resistance change, test methods and criteria
per MIL-PRF-55342.
PART NUMBERING
S 1505 C A 1001 F H B - TR
PACKAGING CODE: - TR = Tape/Reel - W = Waffle Carrier (Default packaging is Bulk)
TERMINATION FINISH: B: Sn60 over nickel barrier W: Gold
TEMPERATURE CHARACTERISTIC TCR: E: ±25 ppm H: ±50 ppm K: ±100 ppm
TOLERANCE: B: 01% C: 0.25% D: 0.5% F: 1% G: 2% J: 5%
RESISTANCE VALUE:
Three or Four digits are used, with all leading digits significant. Four digits are used for 1% tolerance or lower; otherwise, three digits are
used. The last digit specifies the number of zeros to add. The letter "R" is used to represent the decimal for fractional ohmic values.
Example: 5R6 is 5.6 ohms.
PRODUCT DESIGNATION: A: Thin film on alumina
TERMINATION TYPE: C: Wraparound termination
SIZE CODE
GRADE: S: Standard Production H: High Reliability (For Screening options, contact the factory)
MECHANICAL
INCHES
MILLIMETERS
.182
MINIMUM
RECOMMENDED
MOUNTING
PADS
(INCHES)
Length
Width
Thickness
Top Term
Bottom Term
Gap
Approx. Weight
.152 (.150 - .158)
.048 (.046 - .054)
.017 (.013 - .023)
.015 (.010 - .020)
.018 (.010 - .020)
.116 (.112 - .120)
0.0078 grams
3.85
1.22
0.38
0.38
0.45
2.95
(3.80 - 4.00)
(1.17 - 1.37)
(0.33 - 0.58)
(0.25 - 0.50)
(0.25 - 0.51)
(2.85 - 3.05)
.110
.052
.036
“Specifications subject to change without notice.”
STATE OF THE ART, INC.
2470 Fox Hill Road, State College, PA 16803-1797
Phone (814) 355-8004
www.resistor.com
Fax (814) 355-2714
Toll Free 1-800-458-3401
02/15/08
Share a book: Electronic System Design and Practical STM32 FPGA Control Edition
This book is divided into four parts:Part 1, Analog System DesignPart 2, STM32 Application System DesignPart 3, Modern Digital (FPGA) System DesignPart 4, Integrated System DesignFor the specific cont...
generalcircuits stm32/stm8
STM32 Application Experience STM32F107 and STM32F407 Hardware Compatibility Design Considerations
[i=s]This post was last edited by nich20xx on 2020-5-31 05:33[/i]1 Introduction The STM32F407xx and STM32F10XXX series maintain a relatively similar compatibility mode. All functional pins are pin-to-...
nich20xx stm32/stm8
How to choose the inductor for boost circuit? Only three formulas are needed
The BOOST power architecture is a very classic boost power solution. It is a switching power supply that uses the time ratio of the switch tube to maintain a stable output. It is widely used in electr...
wangerxian Power technology
[Pingtou Ge RVB2601 creative application development] Solve NTP by yourself and display electronic clock.
[Preface] RVB2601 establishes a connection with its own server, synchronizes the server time, and initializes the RTC time. Due to problems with the existing NTP component, it has not been fixed after...
lugl4313820 XuanTie RISC-V Activity Zone
Chat with VICOR engineers about high power density, high-grade ZVS buck and buck-boost products
Delivery drones Delivery drones must deliver goods to designated recipients safely and reliably, wherever they are. The greater the distance and the greater the ability to handle heavier and larger lo...
eric_wang Power technology
A microcontroller for less than one dollar?
I saw a 51 MCU MS51FB9AE from Xintang. It has 16KB Flash and all the basic peripheral interfaces. I was amazed at its price of nearly 1 yuan. What cheap ( 1 yuan) MCUs have you used?...
aallian Microcontroller MCU

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号