177-714-5-51GS6K5-24FNN datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-714-5-51GS6K5-24FNN

177-714-5-51GS6K5-24FNN: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-714-5-51GS6K5-24FNN Overview

Interconnection Device

177-714-5-51GS6K5-24FNN Parametric

Parameter Name	Attribute value
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

RC coupled self-excited multivibrator circuit

Electronic "blackboard" circuit for learning Pinyin

Delay circuits controlled by single-junction transistors and thyristors

SANVD brand SV-M912 electric shaver circuit diagram

DC booster circuit suitable for use with multimeters

BQ2000 charge controller

Motor Control Advanced 3——PID Cascade Control (with full code download): The first two articles introduced [PID speed control](https://en.eeworld.com/bbs/thread-1166004-1-1.html) and [PID position control](https://en.eeworld.com/bbs/thread-1166782-1-1.html), which are used...; DDZZ669 Motor Drive Control（Motor Control）

[Evaluation of domestic FPGA Gaoyun GW1N-4 series development board] ——9. Internal OSC and rPLL IP core test: [i=s]This post was last edited by gs001588 on 2022-1-8 12:16[/i][Evaluation of domestic FPGA Gaoyun GW1N-4 series development board] ——9. Internal OSC and rPLL IP core testGW1N-4, GW1N-4B and other se...; gs001588 Domestic Chip Exchange

Zero-Drift Amplifiers: Features and Benefits: Zero-drift amplifiers use a unique self-correcting technique to provide ultra-low input offset voltage (Vos) and near-zero input offset voltage drift over time and temperature (dVos/dT) for general-pu...; Jacktang Analogue and Mixed Signal

Interference issues: It is a 1MHZ PWM signal. The 12V side is stepped down to 5V and fed to the microcontroller. It is found that the 5V power supply has more burrs, causing the PWM output waveform to be distorted. 12V 24...; tangwei8802429 Analog electronics

Help, the SD card cannot communicate normally, and the measured pin voltage is abnormal: When I read and write the SD card, FR_NOT_READY is always returned. The waveforms of the CD and DATA0 pins measured with an oscilloscope are abnormal. The SD card is powered by 3.3V and the processor ...; littleshrimp Integrated technical exchanges

Implement PID using FPGA and simulate with modelsim: It is very common to use a single-chip microcomputer. However, in FPGA, due to floating-point arithmetic problems, it is troublesome to use PID. The following is a PID Verilog program I designed. It s...; wstcllx EE_FPGA Learning Park

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components