EEWORLDEEWORLDEEWORLD

Part Number

Search

LV400M0120BPF42530

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum, 400V, 20% +Tol, 20% -Tol, 120uF,
CategoryPassive components    capacitor   
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

LV400M0120BPF42530 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum, 400V, 20% +Tol, 20% -Tol, 120uF,

LV400M0120BPF42530 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid746289260
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL0
capacitance120 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter25 mm
dielectric materialsALUMINUM (WET)
length30 mm
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package formSnap-in
method of packingBulk
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)400 V
ripple current850 mA
Terminal pitch10 mm
YAGEO CORPORATION
ELECTROLYTIC CAPACITORS
Large Can Aluminum
Electrolytic Capacitors
LV
[ For Long Life ]
For Printed Circuit Board High-Performance Aluminum Electrolytic Power
Supply Input and Output Filter Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature Range -40 to +105°C
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
10 to 100VDC
560 ~ 68000μF
±20% at 120Hz, 20°C
1
0.02CV or 3mA whichever is smaller
(After Rated Voltage Applied for 5 Minutes)
I = Leakage Current (μA), C = Nominal Capacitance (μF),V = Rated Voltage (V)
Dissipation Factor (tanδ)
(20°C, 120Hz)
Rate Voltage (V) 10 16 25 35 50 63 80 100 160 180~400 450
D.F (%)
standard rating
Endurance
400
1.14
10K
1.4
Shelf Life
After the rated voltage has been applied at 105°C for 3000 hours, the
capacitors shall meet the following requirements.
(a) Capacitance Change : Within ±20% of the Initial Value
(b) Dissipation Factor : Not Exceeding 200% of the Specified Value
(c) Leakage current : Not Exceeding the Specified Value
After having been placed at 105°C without voltage applied for 1000 hours,
the capacitors shall meet the same requirements as Endurance.
55 55 45 40 35 30 25
25
15
15
25
Dissipation Factor (tan
δ)
shall not exceed the values showed as above of
-25 to +105°C
160 to 450VDC
270 ~ 2200μF
DESCRIPTION
Features : 105°C 3000 hours, Longer life than LG,
Snap-in terminal, High ripple current.
Recommended Applications : Smoothing circuit, TV/
Monitor, Adapter, SMPS.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
COEFFICIENT
FREQUENCY (Hz)
COEFFICIENT
50
0.8
IK
60
0.85
2.4K
120
1.0
5K
1.36
1.23 1.3
DIAGRAM OF DIMENSIONS
Location of P.C.B. Holes
Vinyl Sleeve
0.9
±
0.1
10
±
0.5
2mm x 2
Unit: mm
10
±
0.5
Negative
Botton Plate
3.0
0.8+0.2/-0.1
5.8
±
1.0
1.5+0.2/-0.1
Safety Device
L+2 Max.
5.8
±
1
D
±
1
Design of Multi-machine Communication Dispatch and Command System with I2C Bus
The structure, working principle and data transmission mode of I2C bus are discussed. The design of multi-machine communication software and hardware based on I2C bus is discussed, and a program-contr...
Aguilera Microcontroller MCU
Tetris_Verilog Course Design.rar
Tetris_Verilog Course Design.rar...
zxopenljx EE_FPGA Learning Park
Will directly connecting the solder joint to the copper pad cause the heat to transfer too quickly and make soldering difficult?
I have a question. I am drawing a board, and the GND pins of several capacitors are very close to the GND copper. I just put the GND pins of the capacitors directly on the copper. Then the software sh...
风轻轻 PCB Design
Several questions about MmwaveStudio
Question 1: What are the parameters for the Sensor configuration option in MmwaveStudio and what are its meanings? There is some confusion when configuring the mmwavestudio sensor configuration option...
qwqwqw2088 Analogue and Mixed Signal
How to Improve Electronic Product Heat Dissipation through Good PCB Design
[align=left][color=rgb(51, 51, 51)]For electronic equipment, a certain amount of heat will be generated when working, which will cause the internal temperature of the equipment to rise rapidly. If the...
okhxyyo PCB Design
The output waveform of the Wien oscillator circuit is abnormal
The output waveform is shown in the figure above, the circuit schematic is as shown below, the op amp power supply is positive and negative 8V No matter how you adjust the sliding rheostat, the output...
S3S4S5S6 Analog electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号