EEWORLDEEWORLDEEWORLD

Part Number

Search

C0805Y682JARAC7210

Description
Ceramic Capacitor, Ceramic,
CategoryPassive components    capacitor   
File Size2MB,21 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Environmental Compliance
Download Datasheet Parametric View All

C0805Y682JARAC7210 Overview

Ceramic Capacitor, Ceramic,

C0805Y682JARAC7210 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7057272904
package instruction, 0805
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL8.1
capacitance0.0068 µF
Capacitor typeCERAMIC CAPACITOR
dielectric materialsCERAMIC
high0.78 mm
JESD-609 codee3
length2 mm
Installation featuresSURFACE MOUNT
multi-layerYes
negative tolerance5%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formSMT
method of packingTR, Embossed Plastic, 13 Inch
positive tolerance5%
Rated (DC) voltage (URdc)250 V
size code0805
surface mountYES
Temperature characteristic codeX7R
Temperature Coefficient15% ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
width1.25 mm
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Floating Electrode Design with Flexible Termination
System (FF-CAP), X7R Dielectric, 6.3 – 250 VDC
(Commercial & Automotive Grade)
Overview
KEMET’s Floating Electrode with Flexible Termination
capacitor (FF-CAP) combines two existing KEMET
technologies– Floating Electrode and Flexible Termination.
The floating electrode component utilizes a cascading
internal electrode design configured to form multiple
capacitors in series within a single monolithic structure.
This unique configuration results in enhanced voltage and
ESD performance over standard capacitor designs while
allowing for a fail-open condition if mechanically damaged
(cracked). The flexible termination component utilizes a
conductive silver epoxy between the base metal and nickel
barrier layers of KEMET’s standard termination system
in order to establish pliability while maintaining terminal
strength, solderability and electrical performance. Both
technologies address the primary failure mode of MLCCs–
flex cracks, which are typically the result of excessive
tensile and shear stresses produced during board flexure
and thermal cycling.
Although neither technology can eliminate the potential for
mechanical damage that may propagate during extreme
environmental and/or handling conditions, the combination
of these two technologies provide the ultimate level of
protection against a low IR or short circuit condition.
The FF-CAP complements KEMET’s Open Mode, Floating
Electrode (FE-CAP), Flexible Termination (FT-CAP) and KEMET
Power Solutions (KPS) product lines by providing an ultimate
fail-safe design optimized for low to mid range capacitance
values. These devices exhibit a predictable change in
capacitance with respect to time and voltage and boast a
minimal change in capacitance with reference to ambient
temperature. Capacitance change is limited to ±15% from
−55°C to +125°C.
In addition to Commercial Grade, Automotive Grade devices
are available which meet the demanding Automotive
Electronics Council's AEC–Q200 qualification requirements.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C
Ceramic
0805
Y
104
Capacitance
Code (pF)
Two significant
digits and
number of
zeros
K
5
R
A
C
TU
Case Size Specification/
(L" x W")
Series
0603
0805
1206
1210
1812
Y = Floating
Electrode
with
Flexible
Termination
Failure Rate/
Capacitance Rated Voltage
Packaging/
Termination Finish
1
Dielectric
Design
Tolerance
(VDC)
Grade (C-Spec)
J = ±5%
K = ±10%
M = ±20%
9 = 6.3
8 = 10
4 = 16
3 = 25
5 = 50
1 = 100
2 = 200
A = 250
R = X7R
A = N/A
C = 100% Matte Sn
L = SnPb (5% Pb
minimum)
See
"Packaging
C-Spec
Ordering
Options
Table"
Additional termination finish options may be available. Contact KEMET for details.
1
SnPb termination finish option is not available on automotive grade product.
1
Built Into Tomorrow
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1015_X7R_FF-CAP_SMD • 9/14/2020
1
Please tell me how to use low power resistors when connecting LEDs in series and parallel
In the picture, the LED is 0.5W/2V, 12 LEDs are connected to 24V, the resistance = 2V*6/250mA*2=24R, right? Then the power of the resistor is 2V*6*250mA*2=6W? Because the chip resistors used are not s...
sky999 LED Zone
Award-winning live broadcast | Interpretation of TI's latest low-cost C2000 features, quickly get started with precision power supply and motor control!
In the evolving automotive and industrial power conversion markets, designers are looking for innovations that can help them address two key design challenges: How can real-time control resources be e...
nmg Microcontroller MCU
Comparison summary of MSP430 FR2xx series MCU BSL and MSP432 P series MCU BSL
[align=left][color=rgb(85, 85, 85)][font="][size=4]The bootloader (BSL) is an application built into the MSP low-power microcontrollers (MCUs). It allows the user to communicate with the MCU to read d...
fish001 Microcontroller MCU
A port to type C port problem
A port to type C port problem...
QWE4562009 Integrated technical exchanges
Build a Prank HID Device with Pico and CircuitPython
In the official blog, element14 introduced a project to build a prank HID device using Pico and CircuitPython.The main idea is to use PICO to emulate the keyboard and mouse sending random keys.[hide]h...
dcexpert MicroPython Open Source section
Simulink and UDS on Can
I would like to ask, can I use simulink to build a diagnostic model for UDS on Can?...
QSQSQS001 Automotive Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号