High Frequency, High Temp, One-Output Clock Generator
The Smart Timing Choice
The Smart Timing Choice
Features
Applications
Frequencies between 115.194001 MHz to 137 MHz accurate to 6
decimal places
Operating temperature from -40°C to 125°C. For -55°C option, refer
to
SiT2020
and
SiT2021
Supply voltage of 1.8V or 2.5V to 3.3V
Excellent total frequency stability as low as ±20 ppm
Low power consumption of 5mA typical at 1.8V
LVCMOS/LVTTL compatible output
5-pin SOT23-5 package: 2.9mm x 2.8mm
RoHS and REACH compliant, Pb-free, Halogen-free and
Antimony-free
For AEC-Q100 clock generators, refer to
SiT2024
and
SiT2025
Industrial, medical, avionics and other high temperature applica-
tions
Industrial sensors, PLC, motor servo, outdoor networking
equipment, medical video cam, asset tracking systems, etc.
Electrical Specifications
Table 1. Electrical Characteristics
[1,2]
Parameters
Output Frequency Range
Symbol
f
Min.
115.194001
Typ.
–
Max.
137
Unit
MHz
Condition
Refer to
Table 14
for the exact list of supported frequencies
list of supported frequencies
Inclusive of Initial tolerance at 25°C, 1st year aging at 25°C, and
variations over operating temperature, rated power supply
voltage and load (15 pF ± 10%).
Frequency Range
Frequency Stability and Aging
Frequency Stability
F_stab
-20
-25
-30
-50
Operating Temperature Range
(ambient)
T_use
-40
-40
Vdd
1.62
2.25
2.52
2.7
2.97
2.25
Current Consumption
Idd
–
–
–
OE Disable Current
Standby Current
I_od
I_std
–
–
–
–
–
Duty Cycle
Rise/Fall Time
DC
Tr, Tf
45
–
–
–
Output High Voltage
VOH
90%
–
–
–
–
–
–
1.8
2.5
2.8
3.0
3.3
–
6.2
5.4
4.8
–
–
2.6
1.4
0.6
–
1.0
1.3
1.0
–
+20
+25
+30
+50
+105
+125
1.98
2.75
3.08
3.3
3.63
3.63
8
7
6
4.8
4.3
8.5
5.5
3.5
55
2.0
2.5
3
–
ppm
ppm
ppm
ppm
°C
°C
V
V
V
V
V
V
mA
mA
mA
mA
mA
A
A
A
%
ns
ns
ns
Vdd
No load condition, f = 125 MHz, Vdd = 2.8V, 3.0V or 3.3V
No load condition, f = 125 MHz, Vdd = 2.5V
No load condition, f = 125 MHz, Vdd = 1.8V
Vdd = 2.5V to 3.3V, OE = Low, output in high Z state.
Vdd = 1.8V, OE = Low, output in high Z state.
Vdd = 2.8V to 3.3V, ST = Low, Output is Weakly Pulled Down
Vdd = 2.5V, ST = Low, Output is Weakly Pulled Down
Vdd = 1.8V, ST = Low, Output is Weakly Pulled Down
All Vdds
Vdd = 2.5V, 2.8V, 3.0V or 3.3V, 20% - 80%
Vdd = 1.8V, 20% - 80%
Vdd = 2.25V - 3.63V, 20% - 80%
IOH = -4 mA (Vdd = 3.0V or 3.3V)
IOH = -3 mA (Vdd = 2.8V or 2.5V)
IOH = -2 mA (Vdd = 1.8V)
IOL = 4 mA (Vdd = 3.0V or 3.3V)
IOL = 3 mA (Vdd = 2.8V or 2.5V)
IOL = 2 mA (Vdd = 1.8V)
Extended Industrial
Automotive
Operating Temperature Range
Supply Voltage and Current Consumption
Supply Voltage
LVCMOS Output Characteristics
Output Low Voltage
VOL
–
–
10%
Vdd
SiTime Corporation
Rev. 1.0
990 Almanor Avenue, Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised October 16, 2014
SiT2019
High Frequency, High Temp, One-Output Clock Generator
The Smart Timing Choice
The Smart Timing Choice
Table 1. Electrical Characteristics
[1,2]
(continued)
Parameters
Input High Voltage
Input Low Voltage
Input Pull-up Impedence
Symbol
VIH
VIL
Z_in
Min.
70%
–
50
2
Startup Time
Enable/Disable Time
Resume Time
RMS Period Jitter
Peak-to-peak Period Jitter
RMS Phase Jitter (random)
T_start
T_oe
T_resume
T_jitt
T_pk
T_phj
–
–
–
–
–
–
–
–
–
Typ.
–
–
87
–
–
–
–
1.6
1.8
12
14
0.5
1.3
Max.
–
30%
150
–
5
130
5
Jitter
2.5
3
20
30
0.8
2
ps
ps
ps
ps
ps
ps
f = 125 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V
f = 125 MHz, Vdd = 1.8V
f = 125 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V
f = 125 MHz, Vdd = 1.8V
f = 125 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
f = 125 MHz, Integration bandwidth = 12 kHz to 20 MHz
Unit
Vdd
Vdd
k
M
ms
ns
ms
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Measured from the time Vdd reaches 90% of final value
f = 115.194001 MHz. For other frequencies, T_oe = 100 ns + 3 *
clock periods
Measured from the time ST pin crosses 50% threshold
Condition
Input Characteristics
Startup and Resume Timing
Notes:
1. All electrical specifications in the above table are specified with 15 pF output load and for all Vdd(s) unless otherwise stated.
2. The typical value of any parameter in the Electrical Characteristics table is specified for the nominal value of the highest voltage option for that parameter and at
25 °C temperature.
Table 2. Pin Description
Pin
1
2
Symbol
GND
NC
Power
No Connect
Output
Enable
3
OE/ ST/NC
Standby
No Connect
4
5
VDD
OUT
Power
Output
Electrical ground
[3]
No connect
H
[4]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
H or Open
[4]
: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode. Supply
current reduces to I_std.
Any voltage between 0 and Vdd or Open
[4]
: Specified frequency
output. Pin 3 has no function.
Power supply voltage
[3]
Oscillator output
4
5
Functionality
Top View
OE/ST/NC NC
3
2
GND
1
VDD
OUT
Notes:
3. A capacitor of value 0.1 µF or higher between Vdd and GND is required.
4. In OE or ST mode, a pull-up resistor of 10 kΩ or less is recommended if pin 3 is not externally driven.
If pin 3 needs to be left floating, use the NC option.
Figure 1. Pin Assignments
Rev. 1.0
Page 2 of 12
www.sitime.com
SiT2019
High Frequency, High Temp, One-Output Clock Generator
The Smart Timing Choice
The Smart Timing Choice
N
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance of the
IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
[5]
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Note:
5. Exceeding this temperature for extended period of time may damage the device.
Table 4. Thermal Consideration
[6]
Package
SOT23-5
JA
, 4 Layer Board
(°C/W)
421
JC
, Bottom
(°C/W)
175
Note:
6. Refer to JESD51 for
JA
and
JC
definitions, and reference layout used to determine the
JA
and
JC
values in the above table.
Table 5. Maximum Operating Junction Temperature
[7]
Max Operating Temperature (ambient)
105°C
125°C
Maximum Operating Junction Temperature
115°C
135°C
Note:
7. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev. 1.0
Page 3 of 12
www.sitime.com
SiT2019
High Frequency, High Temp, One-Output Clock Generator
The Smart Timing Choice
The Smart Timing Choice
Test Circuit and Waveform
[8]
Test
Point
Vout
Vdd
Tr
5
4
0.1µF
Power
Supply
Tf
15pF
(including probe
and fixture
capacitance)
1
2
3
80% Vdd
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
Vdd
1k
OE/ST Function
Figure 2. Test Circuit
Note:
8. Duty Cycle is computed as Duty Cycle = TH/Period.
Figure 3. Output Waveform
Timing Diagrams
90% Vdd
Vdd
50% Vdd
Vdd
Pin 4 Voltage
T_start
No Glitch
during start up
[9]
ST Voltage
T_resume
CLK Output
CLK Output
T_start: Time to start from power-off
T_resume: Time to resume from ST
Figure 4. Startup Timing (OE/ST Mode)
u
Figure 5. Standby Resume Timing (ST Mode Only)
Vdd
50% Vdd
OE Voltage
T_oe
OE Voltage
Vdd
50% Vdd
T_oe
CLK Output
CLK Output
HZ
T_oe: Time to re-enable the clock output
T_oe: Time to put the output in High Z mode
Figure 6. OE Enable Timing (OE Mode Only)
Note:
9. SiT2019 has “no runt” pulses and “no glitch” output during startup or resume.
Figure 7. OE Disable Timing (OE Mode Only)
Rev. 1.0
Page 4 of 12
www.sitime.com
SiT2019
High Frequency, High Temp, One-Output Clock Generator
As a beginner of STM32, I finally finished reading the preliminary Keil+STM32 GPIO today, bought a development board, and practiced it. It's not bad. I also read the startup.s roughly.
Next week’s goa...
[i=s]This post was last edited by littleshrimp on 2021-3-8 15:22[/i]When I bought it, I made sure it had a black and white screen. Looking at the disassembly photos online, most of them showed MSP430G...
Phase Shifter
Phase shifters switch different bypass lines faster than voltage regulators. The figure shows a 4-position switching phase shifter for a radar unit. Different bypass lines are switched t...
Hello everyone, what software are currently used for schematics and wiring diagrams in the automotive industry? Are there any installation packages and tutorials recommended? Thank you...
In principle, a magnetic bead can be equivalent to an inductor, which refers to a pure inductor. However, a real inductor coil has distributed capacitance, which means that the inductor we use is actu...
Last year, iPad Air 4 was surprisingly launched with the 5nm A14 Bionic processor, one month ahead of iPhone 12. At the same time, iPad Air 4 also adopted the feature of fingerprint recognition ...[Details]
Over the past month, rumors that Tencent Music is under antitrust investigation by China's antitrust department, the State Administration for Market Regulation, have been circulating on major media w...[Details]
There is a probability of failure in MCU decryption . From our experience in decryption, there is about a 1% probability of failure in MCU decryption and a 0.3% probability of damaging the mother chi...[Details]
product description
Gas turbine flowmeter
It is a new type of velocity instrument. It has the advantages of high accuracy, good repeatability, simple structure, high pressure resistance, wide mea...[Details]
Major semiconductor manufacturers and professional power supply manufacturers around the world are actively investing in research and development and launching some dedicated IC chips to welcome the a...[Details]
When operating under harsh conditions, even if perfect design specifications are implemented during design, the maintenance rate can be reduced, but routine inspections and preventive maintenance m...[Details]
Overview and measurement principle of RF admittance level meter:
Radio frequency admittance is a new type of level control technology developed from capacitive type, which is anti-hanging, more r...[Details]
1. Angle of Attack
Refers to the forward-inclined three-dimensional angle formed by the moving scraper surface and the plane of the screen during screen printing.
2. Bias
Refers to a ...[Details]
During maintenance, I have come across many types of compressor voltage stabilizers. Although their circuits are different, they all have certain defects, unstable performance, and high failure rat...[Details]
In the field of modern industry and automation, servo motors, as a key motion and control device, are increasingly gaining widespread attention and application. With its precise motion control and ...[Details]
Power system reliability is an important indicator of power system operation. Traditional power system reliability indicators reflect the availability of power system components or networks, but do...[Details]
Sony Xperia’s official Weibo account released a preview poster, indicating that there is still one day left before the release of the Chinese version of Xperia 5, which means that Sony will hold a pr...[Details]
Due to the continued tight power supply in recent days, Suzhou has implemented power rationing measures since September 26. The operation of the Suzhou factories of IC substrate manufacturers Xinxing...[Details]
Vicor, a high-power modular power company, recently announced that its power modules have been successfully applied to Wanwei security robots, allowing the robots to demonstrate their capabilities in...[Details]
October 24, 2024, Tessenderlo, Belgium -
Melexis, a global microelectronics engineering company, announced the launch of the MLX90424, a cost-effective solution that simplifies the automotive b...[Details]