Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
The EFM32PG22 Dev Kit has an I2C interface digital Hall sensor Si7210 on board. The main parameters are as follows:It can be seen that its characteristics are super low power consumption and a built-i...
Author: Dylan ZhengUSB Type-C is becoming more and more popular and is widely used in notebooks, mobile phones, desktops, industrial PCs and other fields. In these applications, the Type-C interface i...
PLL is a commonly used resource in FPGA, which is used to synthesize clocks other than the frequency provided by the external crystal oscillator. EG4S20 has four PLLs, and the use of PLL resources is ...
Misumi data cable driver cannot be installed
Win10 system cannot be installed.The driver can only be used in XP or Win7
KCA-M538F-000
M538F USB High Speed Serial Converter...
After Renesas , NXP , ST and other MCU manufacturers have been out of stock, it is particularly important to find alternatives. In recent years, domestic MCUs have developed rapidly and have a certain...
MSP430 can choose to use up to three oscillators depending on the model. We can choose the appropriate oscillation frequency according to our needs, and we can turn off the oscillator at any time when...
Preface
The role of medical equipment in hospital medical services has become increasingly important, and the technical status management of medical equipment itself is also becoming increasi...[Details]
A few days ago, I saw a piece of news on TV: a military fuel cell drone was exhibited at a certain aviation technology exhibition in South Korea. Since it has been exhibited, I think the South Korean...[Details]
OPPO Reno8 series is equipped with Mariana® MariSilicon X, building a dual-core portrait flagship
May 19, 2022, Shenzhen, China -
OPPO officially announced that the Reno8 series ...[Details]
element14 supplies Aim-TTi's new SMU4000 series source measure units from stock Aim-TTi's new SMU4000 series integrated source measurement solution adopts four-quadrant PowerFlex technology, wi...[Details]
Power secondary equipment mainly refers to equipment that controls, monitors and protects primary equipment, including power station automation, substation automation, dispatching automation, distr...[Details]
Huawei is developing intelligent connected cars. The Internet is influencing people's way of thinking and interaction at an unprecedented depth and speed. As an important field that is indispensable ...[Details]
On January 3, Phase Regulator No. 1 of the Jinhua 2×300 MW Phase Regulator Project was successfully connected to the grid at the ±800 kV Jinhua Converter Station with excellent indicators. In the f...[Details]
Measuring rate, range mode, automatic clearing, and filtering are common ways to adjust the speed. If you want to speed up the test, you can set it according to actual needs. 1. Measurement rate ...[Details]
On June 25, 2020, the Semiconductor Industry Association (SIA) welcomed the Senate’s passage of the American Foundry Act of 2020, legislation that will provide tens of billions of dollars in federal ...[Details]
On June 5, *ST Dongke issued an announcement stating that the company had evaluated the Nanjing CEC Panda 8.5-generation TFT-LCD production line project's asset group in terms of the project's fixed ...[Details]
Texas Instruments (TI)'s (TI) wireless charging chip dominance is being threatened by application processor manufacturers (AP). After Qualcomm announced its joining the Wireless Power Consortium (WPC...[Details]
As the number of NFC phones increases, NFC tags will become a standard feature of NFC phones. However, many Android users still don't know how to use these tags. So try using your NFC tags now.
...[Details]
The Supervisory Board announced that Frits van Hout will retire from ASML after completion of his current term, at the expiration of the 2021 General Meeting of Shareholders on April 29, 2021. Frit...[Details]
Nondestructive testing technology has played an important role in ensuring the safe and reliable operation of aviation equipment and providing technical support. Whether in the manufacturing and pro...[Details]
Development Kits Review Area
京公网安备 11010802033920号
EEWORLD
