Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
Company: Shenzhen Ruizhixin Technology Co., Ltd., a wholly-owned subsidiary of Beijing Wenzhi Technology Co., Ltd.
Work location: Shenzhen Nanshan Zhongguan Times Square
Working hours: Two days off, 9...
This application document introduces the PWM software driving technology of capacitive touch wheel and multiple independent LEDs using MSP430 microcontroller. The solution realizes capacitive touch wh...
5V, 28KHZ pulse, CP1 is not connected, I don't know how big to connect it, 50% square wave goes in, and it always comes out messy. Should R2 be changed to 350R?...
Serial communication is a major data transmission method and is also the only debugging and observation method when there is no display device.
1. Initialization of serial communication
To use serial ...
Cut a certain area of the element
img{clip:rect(23px,14px,45px,54px)}rect (top, right, bottom, left) sets the shape of the elementauto does not apply any clipping###2.Z-Indexsets the stacking order of...
February 27 news (Text/Tan Lun) "Our battery supplier is in Wuhan, and this is the component we need most at the moment." When talking about the impact of the epidemic, Li Dong, sales manager of a sm...[Details]
Sina Digital News reported on the morning of December 23 that industry sources said that Apple has reserved TSMC's production capacity based on 3-nanometer process chips for use in its iOS prod...[Details]
1. Front-end camera point deployment design
School gate: Multiple Jiemai high-definition 1080P gun cameras are used, and the video surveillance platform splicing function is used to achieve 3...[Details]
The serial port initialization configuration is also very simple, as shown below: Among them, the settings of TH1 and TL1 are based on 11.0529MHZ, and the specific settings depend on the actual fre...[Details]
The 2024 (18th) Beijing International Automotive Exhibition officially opened today, with the theme of "New Era, New Car". As a leading company in the automotive supply chain, NavInfo launched the ...[Details]
On November 9, 2023, Arm Technology (China) Co., Ltd. (hereinafter referred to as "Arm Technology") officially released the "Shanhai" S20F security solution. As an HSM (Hardware Security Module) pr...[Details]
In recent years, micro-electromechanical systems (MEMS) technology has revolutionized the audio industry. MEMS technology uses tiny mechanical components to convert electrical signals into sound wa...[Details]
If you need to control the brightness of an LED, you need a driver that can provide a constant, regulated current. To achieve this goal, the driver topology must be able to produce enough output ...[Details]
Cable Requirements
Although DMMs often use unshielded test leads, this connection is generally not appropriate for low-level measurements such as picoammeters, electrometers, and SMUs. These instrume...[Details]
On the evening of November 19, Tianhua Super Clean announced that the controlling shareholder Pei Zhenhua intends to transfer 27.5638 million shares (accounting for 5% of the company's total share ca...[Details]
With the evolution of technology, the safety provided by vehicles to drivers has attracted more and more attention from major car manufacturers. Recently, BMW released the 2024 models for the US mark...[Details]
A certain type of optical cordless mouse uses two AA alkaline batteries. It does not have a power switch. When not in use, it automatically switches the light source on and off at a low duty cycle ...[Details]
"Mountains are steep because of their backbones, people are strong because of their perseverance, and state-owned enterprises prosper because of their real industries." In the past five years, Li D...[Details]
In LED lighting applications, non-isolated BUCK switching power supplies are favored by many customers due to their high efficiency, and they occupy a part of the market share. Represented by SN391...[Details]
On November 2, the 300,000-kilowatt new energy storage project with a total investment of 2.395 billion yuan by Shouhang Energy Group was started and laid the foundation stone in Changji National High...[Details]
Recruitment
京公网安备 11010802033920号
EEWORLD
