QL11253-A608-TR datasheet, PDF

QL11253-A608-TR: DescriptionTelecom and Datacom Connector, 50 Contact(s), Female, Right Angle, Solder and Surface Mount Terminal, Locking, Plug,; CategoryThe connector The connector; File Size90KB，1 Pages; ManufacturerFOXCONN; Websitehttp://www.fit-foxconn.com/

Download Datasheet Parametric View All

QL11253-A608-TR Overview

Telecom and Datacom Connector, 50 Contact(s), Female, Right Angle, Solder and Surface Mount Terminal, Locking, Plug,

Parameter Name	Attribute value
Objectid	2002214889
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	TAPE & REEL PACKAGING
Board mount options	SPLIT BOARD LOCK
body width	0.217 inch
subject depth	0.315 inch
body length	1.127 inch
Body/casing type	PLUG
Connector type	TELECOM AND DATACOM CONNECTOR
Contact to complete cooperation	AU
Contact point gender	FEMALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	70 mΩ
Contact style	BELLOWED TYPE
DIN compliance	NO
Dielectric withstand voltage	250VAC V
Durability	5000 Cycles
empty shell	NO
Filter function	NO
IEC compliance	NO
maximum insertion force	9.7856 N
Insulation resistance	500000000 Ω
Insulator color	BLACK
insulator material	LIQUID CRYSTAL POLYMER
MIL compliance	NO
Plug contact pitch	0.039 inch
Mixed contacts	NO
Installation option 1	LOCKING
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of ports	1
Number of rows loaded	2
Maximum operating temperature	85 °C
Minimum operating temperature	-55 °C
Options	GENERAL PURPOSE
PCB contact pattern	STAGGERED
PCB contact row spacing	1.1938 mm
Plating thickness	30u inch
polarization key	POLARIZED HOUSING
Rated current (signal)	0.5 A
Guideline	UL
reliability	COMMERCIAL
Terminal length	0.087 inch
Termination type	SOLDER AND SURFACE MOUNT
Total number of contacts	50
UL Flammability Code	94V-0
Evacuation force-minimum value	1.946 N

Improve performance in power tool designs with power modules: [align=left]Transferred from: deyisupport[/align] [align=left]Home appliances using power tools, garden tools and vacuum cleaners are driven by electric motors powered by low-voltage (2 to 10 cells) l...; okhxyyo Analogue and Mixed Signal

Know a little about the AD sampling single mode of dsp28335: Three modes are configured: single mode, continuous mode and DMA transfer. Single mode calls the acquisition function once to collect data at a specified AD port, and samples when needed. Continuous m...; fish001 DSP and ARM Processors

[RISC-V MCU CH32V103 Review] - 2: Making an LED flash is not easy: [i=s]This post was last edited by MianQi on 2021-1-28 11:56[/i]Let's look at the wiring first (the tutorial says to directly connect PinA0\PinA1 and LED1\LED2 with jumpers. I'm not used to doing this,...; MianQi Domestic Chip Exchange

SensorTile.box uses air pressure sensors to analyze environmental changes: After the SensorTile.box is flashed with DataLogExtended firmware, the sensor output data waveform can be directly viewed using Unicleo-GUI The following is the data obtained by using the air pressure...; littleshrimp MEMS sensors

Integrated circuit detection method: Editor's note: Although there are ways to replace integrated circuits, disassembly is troublesome after all. Therefore, before disassembly, you should accurately determine whether the integrated circu...; fighting Test/Measurement

When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?: When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...; 深圳小花 MCU

Popular Components