Right Angle Twist-On Plug -
Field Installable - 1 Piece
INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
PART NUMBER
CPFI-RA-2
CABLE TYPE
RG-59, 62
WIRE GAUGE
22
WIRE DECIMAL
.025 (0.64)
JACKET O.D.
.220 (5.59)-.250 (6.35)
1. Identify connector parts. (1 piece)
2. Trim cable as shown. Taking care not to nick the center conductor or outer braid.
3. Use the fingernail to rotate the outer braids clockwise such that 1/32" of the insulation is bared. Then in the same direction rub the
stray braids flat. (Stray or loose braids can cause shorts.)
4. Gently insert the center conductor down the back end of the connector, feeling it into the guide hole. (If the center conductor is not
in place, approximately 1/8” of the center conductor - the part closest to the dielectric - will still be viewable.)
5. Firmly push the cable home (a slight clockwise twist may help with insertion). Then screw the connector on the cable in a clockwise
direction until it is snuggly attached to the jacket. (Right angle connectors provide a lever to aid in twist, therefore do not over twist,
which may cause the jacket and braids to eventually wear out.)
CABLE ASSEMBLY CAUTIONS:
• Series are designed for solid center conductor wire. RG-58 cable will need the center conductor tin dipped (ONLY if it is not a solid
center conductor). This is necessary to provide extra support for step 5.
• RG-MATV-59 cable will require caution when using the fingernail to rotate the braids on cable types that include aluminum foil for the
outer conductor. DO NOT tear or rip the foil conductor to the 1/32” as suggested by step 3.
• RG-62 cable includes trimming the filament to 9/16” as well. Make sure that the filament does not unravel so that it protrudes past this
dimension.
Part
Number
CPFI-RA-2
Cable
Type
RG-59, 62
Wire
Wire
Gauge Decimal
20
.025 (0.64)
Jacket
O.D.
.220 (5.59)-.250 (6.35)
Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • 1-800-243.8814 • Fax: 507-833-6287 • www.cambridgeproducts.com
BNC Connectors
Specifications
INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
The BNC series connector is a commercial quality product that intermates with all
standard double bayonet stud BNC designs. All contacts are captivated for rug-
gedness. The 50 ohm and 75 ohm interfaces are intermateable and provide quick,
reliable connections for instrumentation, medical and LAN applications.
Specifications*
50 Ohm BNC
Electrical Characteristics
Impedance: 50 Ohm nominal
Frequency range: 0-4 GHz
Working voltage: 500 volts RMS at sea level
Dielectric withstanding voltage: 1500 volts RMS at sea level
Corona level: 375 volts minimum at 70,000 feet
Contact resistance: Outer - 0.2 milliohms maximum
Center - 2.1 milliohms maximum
Insulation resistance: 5000 megohms minimum
Environmental Characteristics
Recommended temperature range: -55
O
C to +85
O
C
Moisture resistance: MIL-STD-202
Mechanical Characteristics
Durability: 500 cycles
Force to engage/disengage: 3 lbs. maximum
Cable retention: 20 lbs., RG-58 C/U cable
Materials
Body: Zinc or brass
Contact: Brass, beryllium copper or phosphor bronze
Spring Washer: Beryllium copper
Crimp sleeve: Brass
Insulator: Delrin
®
or TPX Polymethylpentene
Plating: Body - Nickel (except where noted)
Crimp sleeve - Nickel
Contact - Gold
* These values are typical and may not apply to all connectors.
Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • 1-800-243.8814 • Fax: 507-833-6287 • www.cambridgeproducts.com
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
