Modes of Operation and Pin-outs ................................................................................................................................................ 6
Pin-out Top Views................................................................................................................................................................. 6
Test Circuit Diagrams for LVCMOS and Clipped Sinewave Outputs ........................................................................................... 7
Frequency Stability ............................................................................................................................................................. 11
Output frequency and format .............................................................................................................................................. 11
Output Frequency Tuning ................................................................................................................................................... 11
Pin 1 Configuration (OE, VC, or NC) .................................................................................................................................. 12
Control Voltage Bandwidth ................................................................................................................................................. 15
Pull Range, Absolute Pull Range ............................................................................................................................................... 16
I
2
C Control Registers ................................................................................................................................................................. 21
Register Address: 0x00. Digital Frequency Control Least Significant Word (LSW) ............................................................ 21
Register Address: 0x01. OE Control, Digital Frequency Control Most Significant Word (MSW) ......................................... 22
Register Address: 0x02. DIGITAL PULL RANGE CONTROL ............................................................................................ 23
Register Address: 0x05. PULL-UP DRIVE STRENGTH CONTROL .................................................................................. 24
Register Address: 0x06. PULL-DOWN DRIVE STRENGTH CONTROL ............................................................................ 25
Serial Interface Configuration Description.................................................................................................................................. 26
Serial Signal Format .................................................................................................................................................................. 26
Parallel Signal Format................................................................................................................................................................ 27
Parallel Data Format .................................................................................................................................................................. 27
I
2
C Timing Specification ............................................................................................................................................................. 29
I
2
C Device Address Modes ........................................................................................................................................................ 30
Schematic Example ................................................................................................................................................................... 31
Dimensions and Patterns ........................................................................................................................................................... 32
Ordering Information .................................................................................................................................................................. 34
Rev 0.60
Page 2 of 36
www.sitime.com
SiT5357
60 to 220 MHz,
±0.1
to
±0.25
ppm
Elite Platform™ Precision Super-TCXO
Electrical Characteristics
PRELIMINARY
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and 3.3V Vdd
Table 1. Output Characteristics
Parameters
Output Frequency Range
Duty Cycle
Rise/Fall Time
Output Voltage High
Output Voltage Low
Output Voltage Level
Frequency Stability over Temperature
Frequency vs. Temperature Slope
Dynamic Frequency Change to
Temperature Ramp
Initial Tolerance
24-hour holdover stability
Hysteresis Over Temperature
Symbol
F
DC
Tr, Tf
VOH
VOL
V_out
F_stab
ΔF/ΔT
F_dynamic
F_init
F_24_Hold
F_hys
Min.
60.000001
45
–
90%
–
0.8
-0.1
–
–
-1
-0.28
–
–
–
Supply Voltage Sensitivity
Output Load Sensitivity
One-Day Aging
One-Year Aging
20-Year Aging
Frequency Stability over Temperature
Frequency vs. Temperature Slope
Dynamic Frequency Change during
Temperature Ramp
Initial Tolerance
24-hour holdover
Supply Voltage Sensitivity
Output Load Sensitivity
One-Day Aging
One-Year Aging
20-Year Total Stability
Start-up Time
First Pulse Accuracy
F_Vdd
F_load
F_1d
F_1y
F_20y
F_stab
ΔF/ΔT
F_dynamic
F_init
F_24_Hold
F_Vdd
F_load
F_1d
F_1y
F_20y
T
T_start
T_stability
–
–
–
–
–
–
-0.2
0.25
–
–
-1
-0.32
–
–
–
–
–
-4.6
–
–
±2.5
±2
±1
±3
±1
–
5
10
Typ.
–
–
1
–
–
–
–
±2.5
±0.021
–
–
±15
±15
±10
±2.5
±1
±1
±3
±0.5
±1
–
–
±8
±0.07
–
Max.
220
55
–
–
10%
1.2
+0.1
–
–
+1
+0.28
–
–
–
–
–
–
–
–
–
+0.2
+0.25
–
–
+1
+0.32
–
–
–
–
–
+4.6
–
–
Unit
MHz
%
ns
Vdd
Vdd
V
ppm
ppb/°C
ppb/s
ppm
ppm
ppb
ppb
ppb
ppb
ppb
ppb
ppb
ppm
ppm
ppm
ppm
ppb/°C
ppb/s
ppm
ppm
ppb
ppb
ppb
ppb
ppm
ppm
ms
ms
0.5C/min temperature ramp rate
Initial frequency at 25°C inclusive of solder-down
shift at 48 hours after 2 reflows
Per Stratum 3 definition
Vdd ±5%
LVCMOS output, 15 pF ±10%
Clipped sinewave output, 10kΩ, 10 pF ±10%
After 30-days of continued operation
At 25°C
Stratum 3 per GR-1244
Time to first pulse, measured from the time Vdd
reaches 90% of its final value
Time to first accurate pulse within rated stability,
measured from the time Vdd reaches 90% of its final
value
0.5C/min temperature ramp rate
Initial frequency at 25°C inclusive of solder-down shift
at 48 hours after 2 reflows
Per Stratum 3 definition
-40 to 105C
-40 to 85C
-20 to 70C
Vdd ±5%
LVCMOS output, 15 pF ±10%
Clipped sinewave output, 10kΩ, 10 pF ±10%
After 30-days of continued operation
At 25°C
At 25°C
Referenced to (fmax + fmin)/2 over the specified
temperature range
10% - 90% Vdd
I
OH
= -6 mA, (Vdd = 3.3 V, 3.0 V, 2.8 V, 2.5 V)
I
OL
= 6 mA, (Vdd = 3.3 V, 3.0 V, 2.8 V, 2.5 V)
Measured peak-to-peak swing at any Vdd
Referenced to (max frequency + minimum
frequency)/2 over the specified temperature range
Condition
Frequency Coverage
LVCMOS Output Characteristics
Clipped Sinewave Output Characteristics
Frequency Stability - Stratum 3+ Grade
Frequency Stability - Stratum 3 Grade
Start-up Characteristics
Rev 0.60
Page 3 of 36
www.sitime.com
SiT5357
60 to 220 MHz,
±0.1
to
±0.25
ppm
Elite Platform™ Precision Super-TCXO
Table 2. DC Characteristics
Parameters
Supply Voltage
Symbol
Vdd
Min.
2.25
2.52
2.7
2.97
Current Consumption
OE Disable Current
Operating Temperature Range
IDD
I_od
T_use
–
–
-20
-40
-40
Typ.
2.5
2.8
3.0
3.3
Max.
2.75
3.08
3.3
3.63
Unit
V
V
V
V
mA
mA
°C
°C
°C
PRELIMINARY
Condition
Contact
SiTime
for 2.25V to 3.63V continuous supply
voltage support
Supply Voltage
Current Consumption
–
45
44.5
–
–
–
–
Temperature Range
+70
+85
+105
F = 98.304 MHz, No Load
OE = GND, output is weakly pulled down
Extended Commercial
Industrial. Contact
SiTime
for 105
°C
support
Extended Industrial
Table 3. Input Characteristics
Parameters
Input Impedance
Input High Voltage
Input Low Voltage
Pull Range
PR
Symbol
Z_in
VIH
VIL
Min.
–
70
–
Typ.
100
–
–
Max.
–
–
30
Unit
kΩ
%
%
Internal pull up to Vdd
Condition
Input Characteristics
–
OE Pin
Frequency Tuning Range – Voltage Control or I
2
C mode
±6.25, ±10, ±12.5, ±25, ±50, ±80,
±100, ±125, ±150, ±200, ±400,
±600, ±800, ±1200, ±1600,
±3200
90%
–
10
–
Positive
–
2
ppm
Voltage Control Characteristics
Upper Control Voltage
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Bandwidth
Frequency Change Polarity
Pull Range Linearity
Input Voltage Low
Input Voltage High
Output Voltage Low
Output Current High
Leakage in high impedance mode
Input Hysteresis
Input Capacitance
Rise Time
Fall Time
VIL
VIH
VOL
IOL
I_leak
V_hys
C_in
Tr
Tf
VC_U
VC_L
VC_z
VC_c
–
–
–
10
0.5
–
–
–
–
–
–
–
–
–
–
–
–
10%
–
–
–
0.3
–
0.4
–
24
0.4
0.3
3
120
60
75
Vdd
Vdd
MΩ
kHz
%
V
V
V
mA
µA
V
V
pF
ns
ns
ns
Vdd = 3.3V, 30% to 70%
Vdd = 2.5V, 30% to 70%
0.1 Vdd< VOUT < 0.9 Vdd
Vdd = 3.3V
Vdd = 2.5V
Contact
SiTime
for other input bandwidth options
I C Interface Characteristics, 1 MHz, 200 Ohm, 550 pF (Max I
2
C Bus Load)
–
0.7
–
21
5.5
0.2
0.2
–
–
30
40
Rev 0.60
Page 4 of 36
www.sitime.com
SiT5357
60 to 220 MHz,
±0.1
to
±0.25
ppm
Elite Platform™ Precision Super-TCXO
Table 4. Jitter & Phase Noise
Parameters
RMS Phase Jitter (random)
T_phj
–
Spurs
RMS Period Jitter
Peak Cycle-to-Cycle Jitter
1 Hz offset
10 Hz offset
100 Hz offset
1 kHz offset
10 kHz offset
100 kHz offset
1 MHz offset
5 MHz offset
T_jitt
T_jitt_cc
–
–
–
–
–
–
–
–
–
–
–
0.30
-94
2
10
-54
-82
-104
-126
-132
-135
-149
-155
–
–
–
–
Phase Noise
–
–
–
–
–
–
–
–
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps
dBc
ps
ps
Symbol
Min.
Typ.
Max.
Jitter
–
0.30
–
ps
Unit
PRELIMINARY
Condition
f = 98.304 MHz, Integration bandwidth = 12 kHz to 20
MHz
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20
MHz
f = 98.304 MHz, 12 kHz to 5 MHz offsets
f = 98.304 MHz per JESD65 standard
f = 98.304 MHz per JESD65 standard
f = 98.304 MHz, TCXO and DCTCXO modes, and
VCTCXO mode with ±6.25 ppm pull range
Table 5. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part.
Actual performance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Continuous Power Supply Voltage Range (Vdd)
Human Body Model (HBM) ESD Protection
Soldering Temperature (follow standard Pb-free
soldering guidelines)
Junction Temperature
[1]
Note:
1. Exceeding this temperature for an extended period of time may damage the device.
[i=s]This post was last edited by jinglixixi on 2020-8-23 09:17[/i]1. I2C bus simulation and BH1750 light intensity detection
BH1750 is a digital light intensity sensor based on the I2C interface. We ...
Manual compilation
When it comes to compiler issues, it must be GNU's famous GCC, which also includes related connectors and assemblers.
The GCC for arm is of course arm-linux-gcc. The version I use i...
What is an antenna vibrator : https://training.eeworld.com.cn/course/5791This course will share with you some basic knowledge about antenna oscillators....
I finally received the development board today. When I unpacked it, I saw the development board and debugging tools shown in Figure 1.Figure 1 Development board and debugging tools
After power-on, exc...
Electric motorcycles have become popular in the market in recent years due to their advantages of energy saving, emission reduction, space saving and easy driving, and their sales have been rising ste...
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
