Standard Frequencies – see Page 5 for developed frequencies.
* Check with factory for availability of frequencies not listed.
Applications
Automotive Electronics
Mobile Multimedia/Infotainment
Car Navigation Systems
Internet of Things [IoT, IIot]
Microcontrollers and FPGAs
Wireless Communication
Ethernet/GbE/SyncE
Medical Electronics
Commercial Military & Aerospace
Description
CTS Model SA324 incorporates a low cost, high Q, small size quartz resonator specifically developed to operate
over extended temperature ranges for use in automotive electronics.
Ordering Information
Model
SA324
Frequency Code
[MHz]
XXX or XXXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
5
Temperature
Range
G
Load
Capacitance
A
Packaging
R
Code
Frequency
Product Frequency Code
1
Code
1
X
2
3
5
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
±50ppm
Code
I
G
H
N
P
M
Code
X
2
3
5
6
7
Stability
±15ppm
±20ppm
±30ppm
±50ppm
±100ppm
±150ppm
Temp. Range
-40°C to +85°C
2
-40°C to +105°C
3
-40°C to +125°C
4
-40°C to +150°C
5
-55°C to +105°C
5
-55°C to +125°C
5
Packing
Code
3k pcs./reel
R
Code
F
T
Mode
Fundamental
3rd Overtone
Code Capacitance Code Capacitance
7pF
16pF
V
C
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
13pF
Series
B
S
Notes:
1]
2]
3]
4]
5]
Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
Available with all stability codes.
Available with stability codes 3, 5, 6 and 7.
Available with stability codes 5, 6 and 7.
Stability codes 6 and 7. Contact factory for code 5 availability.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
1. What is a comparator?The function of a comparator is to compare two or more data items to determine whether they are equal, or to determine the size relationship and arrangement order between them,...
[i=s]This post was last edited by xusiwei1236 on 2022-6-19 12:07[/i]This article will introduce how to use RT-Thread's SDIO driver and FATFS file system components on the HPM6750EVKMINI development bo...
I want to use a signal generator to generate a 2mV sine wave, but when I use an oscilloscope to measure it, the waveform shows a lot of noise. How can I solve this problem?...
Click here to view the award ceremonyRISC-V is developing rapidly, and the forum has collected many RISC-V MCUs for everyone to evaluate.
It is unknown how far RISC-V will grow in the future, but we c...
StartFragment
1. The structure and light-emitting principle of LED
50 years ago, people already knew the basic knowledge that semiconductor materials can generate light, and the first...[Details]
The TX-1C board operates the 1602 LCD in parallel mode. Pins 1 and 2 of the LCD are gnd and vcc. Pin 3 is the contrast adjustment. Pin 4 is the data/command selection terminal RS. Pin 5 is the read/w...[Details]
In recent years, large and small urban road traffic accidents have occurred frequently, a large part of which occurred in the blind spots of urban road monitoring. If we only rely on limited traffic ...[Details]
On February 23, the "Airport Line" autonomous driving manned demonstration from Beijing Daxing International Airport to Beijing Yizhuang was officially launched, marking the official opening of the...[Details]
This is the circuit diagram of an audio/video modulator. This circuit converts audio and video signals into UHF TV signals. It is desirable to connect the video signal originating from a camera or ...[Details]
Hello everyone, through the previous study, we have learned and become familiar with the use and learning methods of ICD2 simulation burner and enhanced PIC experiment board, and learned how to use s...[Details]
PEPS refers to Keyless entry and keyless start system (Passive Entry & Passive Start System), this technology is widely used in vehicle access control Keyless entry systems, vehicle keyless start ...[Details]
Preparation Before designing your first power supply, make sure that the printed circuit board used for the power supply follows the layout guidelines specified in the Power Integrations device data...[Details]
StoreDot has announced that it has passed a major milestone, becoming the first company in the world to surpass 1,000 cycles of its XFC batteries (with silicon as the anode).
Usi...[Details]
1 Overview
IMP809/810 is a set of CMOS monitoring circuits newly developed by IMP Company. It can monitor the power supply voltage of 3~5V for low-power microcontroller MCU (or μC), microproces...[Details]
System clock and frequency division First, a passage from the manual. Three different clock sources can be used to drive the system clock (SYSCLK) HSI Oscillator Clock HSE Oscillator Clock PLL Clo...[Details]
The EPC team will be presenting 11 presentations on GaN technology and applications at the APEC 2020 exhibition in New Orleans, USA, from March 15 to 19 (see chart below). In addition, the EPC booth ...[Details]
Stepper motors are now well known to most people and have been widely used. This is of course determined by their own advantages and performance. In particular, the step value of the motor is not aff...[Details]
Taking the common infrared gas detector as an example, the principle of the gas detector is explained:
Measuring this absorption spectrum can identify the type of gas; measuring the absorption ...[Details]
summary
The fifth article in this series explains the importance of auxiliary power in the Analog Devices Battery Backup Unit (BBU) reference design. Auxiliary power consists of a ...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
