Standard Frequencies – see Page 5 for developed frequencies.
* Check with factory for availability of frequencies not listed.
Applications
Automotive Electronics
Mobile Multimedia/Infotainment
Car Navigation Systems
Internet of Things [IoT, IIot]
Microcontrollers and FPGAs
Wireless Communication
Ethernet/GbE/SyncE
Medical Electronics
Commercial Military & Aerospace
Description
CTS Model SA324 incorporates a low cost, high Q, small size quartz resonator specifically developed to operate
over extended temperature ranges for use in automotive electronics.
Ordering Information
Model
SA324
Frequency Code
[MHz]
XXX or XXXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
5
Temperature
Range
G
Load
Capacitance
A
Packaging
R
Code
Frequency
Product Frequency Code
1
Code
1
X
2
3
5
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
±50ppm
Code
I
G
H
N
P
M
Code
X
2
3
5
6
7
Stability
±15ppm
±20ppm
±30ppm
±50ppm
±100ppm
±150ppm
Temp. Range
-40°C to +85°C
2
-40°C to +105°C
3
-40°C to +125°C
4
-40°C to +150°C
5
-55°C to +105°C
5
-55°C to +125°C
5
Packing
Code
3k pcs./reel
R
Code
F
T
Mode
Fundamental
3rd Overtone
Code Capacitance Code Capacitance
7pF
16pF
V
C
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
13pF
Series
B
S
Notes:
1]
2]
3]
4]
5]
Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
Available with all stability codes.
Available with stability codes 3, 5, 6 and 7.
Available with stability codes 5, 6 and 7.
Stability codes 6 and 7. Contact factory for code 5 availability.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
[i=s]This post was last edited by sonicfirr on 2022-4-16 10:22[/i]After NTP timing is successful, the creative project continues to enable RTC and initializes RTC using the time obtained by NTP so tha...
#Lora low power consumption# Use a power analyzer to evaluate the standby power consumption of a lora development board. The low power consumption analysis when LCP=3s is as follows:1. This test only ...
1. The units of electromotive force and voltage are the same, both are volts (V) 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 390307 ...
TI will work with you to create a new driving experience in the future - in-depth learning: Comment on star products and vote for them. The activity has begun~~Click here to enter the eventEvent time:...
2.2 Initial oscillation elimination scheme
Based on the above analysis, it can be seen that if the initial state W of the impulse filter is pre-set to the value after it reaches the stable state...[Details]
1 Introduction
The energy and environmental crisis brought about by the rapid development of modern transportation has become a global problem. Developing electric vehicles and using clean energy is ...[Details]
Not long ago, Samsung released the new generation flagship Galaxy S21 series, including three models: S21, S21+ and S21 Ultra. The series is now on sale through global channels. Surprisingly,...[Details]
When I was about to play with the advanced timer TIM1 / TIM8 on STM32F103ZET6, I suddenly found some port multiplexing problems: The pins of TIM1 are as follows: The pins of USART2 are as follows: ...[Details]
Working principle of gas ultrasonic flowmeter Vortex gas flowmeter Orifice gas flowmeter V cone gas flowmeter price manufacturer Source: Author: 1 Hits: 345 times Time: 2011-11-21 14:01:20 share to: ...[Details]
;Use 51 single-chip microcomputer to design a counting and display system, requiring 8 digital tubes to display the number of pulses input to T1. ;It is best to use assembly language, add comments, ...[Details]
Sina Digital News reported on the morning of July 23 that Samsung Galaxy's new product launch conference will be held on August 5, Beijing time, and it is expected to release products such as t...[Details]
On the evening of February 28, Anker Innovations announced that the company plans to increase the investment amount and source of funds: the original planned investment amount for the "Shenzhen Produ...[Details]
Receiving timing signal generation circuit
As can be seen from the figure, the method of generating the timing signal is the same as the sending timing signal, so the waveform is omitted. It sho...[Details]
1. Download the original driver from the official website
http://www.ralinktech.com/en/04_support/license.php?sn=5016
and put the driver code in the directory /home/tango/code/linux-2.6.3...[Details]
One instruction of DS1302 is one byte with 8 bits in total, of which the 7th bit (the highest bit) is fixed to 1. If this bit is 0, then writing it is invalid. The 6th bit is to select RAM or CLOCK. ...[Details]
I2C: synchronous serial 2-wire communication (one clock line SCL, one data line SDA) is a serial bus The main feature of the I2C bus is its simple interface. Two lines can connect multiple device...[Details]
According to the China Trade Relief Information Network, on June 21, 2021, the U.S. International Trade Commission (ITC) issued an announcement stating that it had made a 337-part final ruling on cer...[Details]
The previous stage completed the configuration of Nor Flash. This stage mainly completes the read and write driver of Nand Flash.
Porting u-boot 1.1.6 to TQ2440 development board - Phase 4
Add ...[Details]
The wiring method of the servo motor encoder plug wire is crucial to ensure the normal operation and precise control of the servo motor. This article will introduce the wiring method of the servo m...[Details]
XuanTie RISC-V Activity Zone
京公网安备 11010802033920号
EEWORLD
