Ordering Information .................................................................................................................................................................... 2
Dimensions and Patterns ― 3.2 x 2.5 mm................................................................................................................................. 14
Dimensions and Patterns ― 5.0 x 3.2 mm................................................................................................................................. 14
Dimensions and Patterns ― 7.0 x 5.0 mm................................................................................................................................. 15
Additional Information ................................................................................................................................................................ 16
Revision History ......................................................................................................................................................................... 17
Rev 1.07
Page 3 of 17
www.sitime.com
SiT3372
1 MHz to 220 MHz Ultra-low Jitter Differential VCXO
Electrical Characteristics
Table 2. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with standard
output termination shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
1
-15
-25
-35
-50
Operating Temperature Range
T_use
-20
-40
-40
-40
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
Pull Range
PR
Typ.
–
–
–
–
–
–
–
–
–
3.3
3.0
2.8
2.5
Max.
220
+15
+25
+35
+50
+70
+85
+95
+105
3.63
3.3
3.08
2.75
Unit
MHz
ppm
ppm
ppm
ppm
°C
°C
°C
°C
V
V
V
V
ppm
See the APR (Absolute Pull Range)
Table 11.
Contact SiTime
for custom pull range options
Voltage at which maximum frequency deviation is guaranteed
Voltage at which minimum frequency deviation is guaranteed
Contact SiTime
for other input bandwidth options
Extended Industrial
Extended Commercial
Industrial
Condition
Accurate to 6 decimal places
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variations, and first year aging at 25
°C,
with VIN voltage at Vdd/2.
±15
ppm is only guaranteed for pull range up to
±100
ppm.
Frequency Range
Frequency Stability
Temperature Range
Supply Voltage
Voltage Control Characteristics
±25, ±50, ±80, ±100, ±150,
±200, ±400, ±800, ±1600,
±3200
90%
–
–
–
–
–
–
10
10
–
–
10%
–
–
1.0
–
Input Characteristics
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Startup Time
OE Enable/Disable Time
VIH
VIL
Z_in
DC
T_start
T_oe
70%
–
–
45
–
–
–
–
100
–
–
–
–
30%
-
55
3.0
3.8
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value
f = 156.25 MHz. Measured from the time OE pin reaches
rated VIH and VIL to the time clock pins reach 90% of swing
and high-Z. See
Figure 9
and
Figure 10
Pin 2, OE
Pin 2, OE
Pin 2, OE logic high or logic low
Upper Control Voltage
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Bandwidth
Pull Range Linearity
Frequency Change Polarity
VC_U
VC_L
VC_z
V_c
Lin
–
Vdd
Vdd
MΩ
kHz
%
Positive Slope
Output Characteristics
Startup and OE Timing
Rev 1.07
Page 4 of 17
www.sitime.com
SiT3372
1 MHz to 220 MHz Ultra-low Jitter Differential VCXO
Table 3. Electrical Characteristics – LVPECL Specific
Parameter
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
RMS Period Jitter
[4]
RMS Phase Jitter (random)
Symbol
Idd
I_OE
I_leak
I_driver
VOH
VOL
V_Swing
Tr, Tf
T_jitt
T_phj
Min.
–
–
–
–
Vdd-1.15
Vdd-2.0
1.2
–
–
–
Typ.
78
53
0.15
–
–
–
1.6
225
1.0
0.225
Max.
92
61
–
33
Vdd-0.7
Vdd-1.5
2.0
290
1.6
0.270
Unit
mA
mA
A
mA
V
V
V
ps
ps
ps
Condition
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz, all
Vdd levels, includes spurs, pull range =
±100
ppm. Temperature
ranges -20 to 70°C and -40 to 85°C
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz, all
Vdd levels, includes spurs, pull range =
±100
ppm. Temperature
ranges -40 to 95°C and -40 to 105°C
f = 156.25 MHz, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, includes spurs, all Vdd
levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz, all
Vdd levels, includes spurs, pull range =
±100
ppm. Temperature
ranges -20 to 70°C and -40 to 85°C
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz, all
Vdd levels, includes spurs, pull range =
±100
ppm. Temperature
ranges -40 to 95°C and -40 to 105°C
f = 156.25 MHz, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, includes spurs, all
I am a student at the School of Microelectronics of Xidian University, engaged in analog circuit design. I don't know much about the industry prospects and employment. I would like to consult my senio...
Wireless connection:Our W800 is a SOC with built-in WIFI, so its focus is on wireless networking. I will just briefly explain the application process: the device needs to connect to the router wireles...
RISC-V Complete Learning Manual ( Based on Longan Development Board )
Preface
Some time ago, I developed a strong interest in RISC-V products and wanted to get started to explore them . In this contex...
DSP enforces byte alignment for char, short, and int, which means char is aligned by byte, int is aligned by 4 bytes, and short is aligned by 2 bytes. So when char* points to 0x1, using (int*)char* ac...
Introduction to the topic: Content: Compare "89C51" and "STM8"; Source: derived from actual use; Function: To support comparison and provide reference for subsequent development; PCB environm...[Details]
1. μC/OS-Ⅱ Overview Most of the work of porting μC/OS-Ⅱ to a specific processor is focused on the implementation of multi-task switching. This part of the code is mainly used to save and restore the ...[Details]
Since 2020, affected by multiple uncertain factors such as the COVID-19 pandemic and intensified Sino-US trade frictions, both the demand side of the terminal market and the upstream supply side have...[Details]
This lecture mainly implements the implementation of usart TX, which is mainly divided into several parts of application 1. Implementation of USART 1 Tx polling (with printf implementation) 2. Im...[Details]
On December 20, CATL signed a deepening strategic cooperation agreement with Avita Technology in Chongqing. Qu Tao, General Manager of the Strategic Investment Planning Department of CATL, and ...[Details]
In accordance with the requirements of the "Notice on Further Clarifying the Electricity Price Policy for Centralized Charging and Swapping Facilities for Electric Buses" (Lu Development and Reform...[Details]
This article introduces the main features, block diagram and typical application circuit of TPS65137. TI's TPS65137 is an active matrix OLED (AMOLED) power solution, including a boost converter wit...[Details]
On June 15, 2012, the second Beijing International Energy Storage Conference CES2012, co-organized by China Energy Storage Research Institute and China Energy Storage Network, was held at the Beiji...[Details]
The automated management and operation system has become an indispensable part of modern enterprises. The video image transmission monitoring system has been widely used in important occasions such...[Details]
1999 is the 50th anniversary of the founding of our country. Over the past 50 years, the people of all ethnic groups in our country have made great achievements in socialist revolution and socialist...[Details]
Some time ago, the attitudes of "Chinese parents" who circulated on the Internet when facing children at different stages of learning were quite vivid: 1-3 grades, they understand and educate patient...[Details]
A soft starter is an electrical device used to start a motor. It can effectively reduce the current shock during starting and extend the service life of the motor and equipment. There are two main ...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
