177-710-1-67P6J7-18PNN datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-710-1-67P6J7-18PNN

177-710-1-67P6J7-18PNN: DescriptionD Microminiature Connector, 67 Contact(s), Male, Plug,; CategoryThe connector The connector; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-710-1-67P6J7-18PNN Overview

D Microminiature Connector, 67 Contact(s), Male, Plug,

177-710-1-67P6J7-18PNN Parametric

Parameter Name	Attribute value
Objectid	7004364785
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	STANDARD: MIL-DTL-83513
Body/casing type	PLUG
Connector type	D MICROMINIATURE CONNECTOR
Contact point gender	MALE
DIN compliance	NO
empty shell	NO
Filter function	NO
IEC compliance	NO
insulator material	LIQUID CRYSTAL POLYMER/POLYPHENYLENE SULFIDE
MIL compliance	YES
Plug information	MULTIPLE MATING PARTS AVAILABLE
Mixed contacts	NO
Installation type	CABLE
Options	GENERAL PURPOSE
Shell surface	CADMIUM
Shell material	ALUMINUM ALLOY
Total number of contacts	67

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

Ultra-low dropout linear voltage regulator circuit

70-watt switching power supply integrated circuit diagram based on KA2S0880

Interface between AD7710 and ADSP-2105

Light meter circuit with LED display

A five-fold frequency multiplication circuit composed of a 556

555 fantasy lantern control circuit

About DS18B20 in stm32f103vet6 industrial control board: I use the STM32F103vet6 industrial control board and DS18b20 water temperature sensor probe bought on Taobao. After the wires are connected, the serial assistant always shows 25 degrees, and there is ...; lhwqwer stm32/stm8

MSP430 CPU and MSP430X CPU: [i=s]This post was last edited by fish001 on 2019-10-11 22:08[/i]MSP430 CPU refers to the 16-bit CPU used in the MSP430F1xx series, with a data bus width of 16 bits, an address bus width of 16 bits, a...; fish001 Microcontroller MCU

EMC conducted emission receiver coupling method: ESCI cannot input DC level. The receiver manual will indicate that for DC-coupling, the max. DC voltage is 0 V. Is the EMC conducted emission test voltage AC or DC? If it is AC, what is the frequency?...; 嗯哼哼 Test/Measurement

Showing off the goods + the board that got me into it: This content is originally created by EEWORLD forum user neilperry . If you want to reprint or use it for commercial purposes, you must obtain the author's consent and indicate the source.Participatio...; neilperry Special Edition for Assessment Centres

EEWorld 15th Anniversary Tool DIY Event Summary: Judging from the 15th anniversary forum tool collection activity, the enthusiasm of engineers for tools still surprised Guanzi~Without further ado, and taking into account public opinion and feasibili...; EEWORLD社区 DIY/Open Source Hardware

I need help from the experts on a question about proteus8: I wrote an interrupt function, which can be run smoothly on Keil, but it cannot be run on Proteus, and the error displayed is a bit strange. I am using stc89c52.Please help me take a look, thank you v...; Gochimedes 51mcu

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components