85°C ± 2°C, 85%±5%RH, 1000 hours; 1.5 hr ON, 0.5 hr OFF cycle
85°C ± 2°C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle
+155°C, 1000 hours
* Depends on resistance value, please contact KOA Speer for details.
Precautions for Use
• The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts
absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human
Body Model 100pF, 1.5kΩ) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged
on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards.
• Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc.
The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na＋), chlorine (Cl−) etc. Therefore these
kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since
lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
• Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk
may happen that the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of
protecting coat may be dropped down. Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
• Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. 5~35°C/35~75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like
hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
●
The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that
the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant
masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product.
For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
11/06/17
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
[color=#000][font="][size=12px]My STLINK occasionally fails to download.[/size][/font][/color][align=left][color=rgb(0, 0, 0)][font="][size=12px]It was like this last time at night, and it was fine th...
No nonsense here, just two notifications!1. The evaluation channel will launch evaluation experience coupons for general evaluation activities (except special activities such as ST competitions, etc.)...
Author: Huang Gang, a member of Yibo Technology Expressway Media"Our DDR3 runs very stably!", "Our DDR4 system has sufficient operating speed and bandwidth!" When everyone is still immersed in the sta...
It’s been a few days since I received the development board, but I haven’t posted anything yet. Today is the first post because I feel like I still don’t understand what the Flathead Brother is!First,...
What types of consumer electronics are PCB boards suitable for?Basically, all electronic products need to use PCB boards, but not every appliance needs a circuit board, and simple appliances may not n...
Principle:
The key to this project is that FSK is a continuous phase, and the frequency of the high level and the low level are not multiples (1200Hz and 2200Hz). It is not easy to determine th...[Details]
Foreign media reported that the International Civil Aviation Organization (ICAO) announced on the 22nd that it would ban passenger planes from transporting lithium-ion batteries as cargo, after pil...[Details]
On January 11, the Zhejiang Regulatory Bureau disclosed the public filing documents for coaching of Hangzhou Guoxin Technology Co., Ltd. (hereinafter referred to as Guoxin Technology). It was disc...[Details]
Now the whole country is developing new energy. The energy storage and load are the same, but the power generation methods are different and the resources are complementary. It is inevitable to integr...[Details]
The instantaneous current impact during the power supply startup process is very large, which has a serious impact on the service life of the power supply and devices. Using a good control method t...[Details]
PID is proportional differential control. You can refer to the automatic control course for detailed introduction! In temperature control, positive action and negative action mean heating when posi...[Details]
The power frequency inverter is popular among electronic production enthusiasts for its simple circuit, easy to make and adjust for beginners, strong overload resistance, low cost and practicality.
...[Details]
introduction
With the development of science and technology, the printing industry has begun to shift from traditional analog production to digital production. As the core coloring device of ...[Details]
As new features continue to be added to portable devices, innovative design solutions that save power are becoming increasingly important. The need for equipment to run longer is also greatly affecti...[Details]
Today, let's first play with the compilation and downloading of the Linux kernel. 1. Background Development environment: 64-bit Ubuntu 14.04; Compilation tool: arm-linux-gcc 4.4.3; Download tool: S...[Details]
Thermistor Testing
In a typical laser diode module, the thermistor has a nominal resistance of 10 kΩ at 25°C. In normal operating mode, the thermal stability of the entire module is more critical tha...[Details]
Solar photovoltaic technology is a technology that converts solar energy into electricity. Its core is a semiconductor material that can release electrons. The most commonly used semiconductor materi...[Details]
New energy vehicles have entered a period of vigorous development in 2023. The penetration rate of new energy vehicles has reached about 35% throughout the year, and even exceeded 44% in some months....[Details]
At MODEX 2024, Schneider Electric announced the release of two new
collaborative robots
: Lexium RL 3 and RL 12, and the Lexium RL 18 model later this year. From single-axis machine tools t...[Details]
1 What is hot swap? During hot swapping , a card or module can be inserted or removed from a live power bus without affecting the overall system. This idea probably came from telephone line cards, w...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
