DR22 SERIES
|
AC OUTPUT
DIN RAIL MOUNT SOLID STATE RELAYS
Features
•
•
•
•
•
•
•
•
•
Output ratings up to 35 Amps at 600 VAC
Built-in overvoltage protection
Relay or Contactor configuration
Integral heat sink eliminates the need for complex thermal
calculations
DBC substrate for superior thermal performance
“Elevator” screw option to allow the use of ring or lug type
terminals
IP20 touch-safe housing
AC or DC control
C-UL-US and TUV approved
PRODUCT SELECTION
Control Voltage
90-280 VAC/VDC
4-32 VDC
20 A
DR2260A20x
DR2260D20x
30 A
DR2260A30x
DR2260D30x
35 A
DR2260A35x
DR2260D35x
SPECIFICATIONS
Output
(1)
Description
Operating Voltage (47-440Hz) [Vrms]
Transient Overvoltage [Vpk]
3
Maximum Off-State Leakage Current @ Rated Voltage [mArms]
Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec]
Load Current, General Use UL508/LC A IEC 62314 @ 40°C [Arms]
Load Current, Motor Starting UL508 FLA/LC B IEC 62314 @ 40°C [Arms]
Minimum Load Current [mArms]
Maximum 1 Cycle Surge Current (50/60Hz) [Apk]
Maximum On-State Voltage Drop @ Rated Current [Vpk]
Maximum 1/2 Cycle I² t for Fusing (50/60Hz) [A² sec]
Minimum Power Factor (at Maximum Load)
4
Motor Rating UL 508/IEC62314 [HP (kW)]: 120 VAC
Motor Rating UL 508/IEC62314 [HP (kW)]: 240 VAC
Motor Rating UL 508/IEC62314 [HP (kW)]: 480 VAC
20 A
48-600
1200
1
500
20
8.5/4.8
100
286/300
1.35
409/375
0.5
0.5 (0.37)
1.5 (1.1)
3 (2.24)
30 A
48-600
1200
1
500
30
14/7.6
100
716/750
1.35
2563/2343
0.5
1 (0.74)
3 (2.2)
5 (3.7)
35 A
48-600
1200
1
500
35
26/14
150
1290/1350
1.30
8320/7593
0.5
2 (1.5)
5 (3.73)
10 (7.4)
Page 1
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
Input
(1)
Description
Control Voltage Range
Maximum Reverse Voltage
Minimum Turn-On Voltage
Must Turn-Off Voltage
Minimum Input Current (for on-state)
Maximum Input Current
Nominal Input Impedance
Maximum Turn-On Time [msec]
Maximum Turn-Off Time [msec]
DR2260Dxxx
4-32 VDC
5
-32 VDC
4 VDC
1 VDC
10 mA
15 mA
Current Regulated
1/2 Cycle
7
1/2 Cycle
DR2260Axxx
90-280 VAC/VDC
6
-
90 VAC/VDC
5 VAC/VDC
6 mA
10 mA
Current Limited
20
30
General
(1)
Description
Dielectric Strength, Input to Output (50/60Hz)
Dielectric Strength, Input/Output to Case (50/60Hz)
Minimum Insulation Resistance (@ 500 VDC)
Maximum Capacitance, Input/Output
Ambient Operating Temperature Range
8
Ambient Storage Temperature Range
Short Circuit Current Rating
9
Weight (typical)
Housing Material
Heat Sink Material
Din Rail Clip Material
Hardware Finish
Input Terminal Screw Torque Range (lb-in/Nm)
Load Terminal Screw Torque Range (lb-in/Nm)
Humidity
LED Input Status Indicator
Parameters
4000 Vrms
4000 Vrms
10
9
Ohms
8 pF
-40 to 80 °C
-40 to 100 °C
100kA
Option “U” 10.5 oz (298 g), Option “V”,“W” 10.6 oz (301 g)
UL94 V-0
Aluminum
Zink Plated Steel
Nickel Plating
Option “U” 13-15/1.5-1.7, Option “V”,“W” 5/0.5
10
Option “U” 13-15/1.5-1.7, Option “V”,“W” 18-20/2-2.2
95% non-condensing
Green
Page 2
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
INPUT CURRENT INFORMATION
4-32 VDC Input
90-280 VAC/VDC Input
SURGE CURRENT INFORMATION
DR2260x20x
DR2260x30x
DR2260x35x
THERMAL DERATE INFORMATION
8
DR2260x20x
DR2260x30x
DR2260x35x
Page 3
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
EQUIVALENT CIRCUIT BLOCK DIAGRAMS/WIRING DIAGRAM
DC Control
AD/DC Control
Recommended Wire Sizes
Terminal
Configuration
Output
13
Relay “U” suffix
Input
Relay “U” suffix
Output Contactor
“V” &“W” suffixes
Screw
Spring
Wire Size
(Solid / Stranded)
2 x 18 AWG (1 mm
2
) Stranded
2 x 10 AWG (6 mm
2
) Stranded
2 x 18 AWG (1 mm
2
) Stranded
2 x 12 AWG (4 mm
2
) Stranded
2 x 20 AWG (0.75 mm
2
) [minimum]
2 x 10 AWG (6 mm
2
)
2 x 8 AWG (10 mm
2
) [maximum]
30 AWG (0.05 mm
2
) [minimum]
12 AWG (3.3 mm
2
) [maximum]
26 AWG (0.13 mm
2
) [minimum]
12 AWG (3.3 mm
2
) [maximum]
Wire Pull-Out
Strength (lbs)[N]
20 [88]
60 [266]
20 [88]
40 [177]
25 [111]
80 [355]
90 [400]
4.5 [20]
30 [133]
5 [22]
5 [22]
Input Contactor
“V” &“W” suffixes
Page 4
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
MECHANICAL SPECIFICATIONS
*Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters]
Input Connector
Screw
Terminal
Spring
Terminal
Protective Earth Connection
10-32
Thread
Protective Earth (PE) screw type
recommended is 10-32 UNC standard not
provided with SSR. Through the use of
a DIN rail ground (protective conductor)
terminal block, the DIN rail itself can be
used as the grounding bus bar. In this
case, the zinc plated steel material used
for the DIN rail clip of DR22 models,
permits a secure path to ground and avoid
the need of a further PE connection.
TABLE 1. Compatible Terminals
Elevator Screw (Suffix ‘W’)
Terminals
Crydom Part
No.
Width [W]
in (mm)
Stud Size Dia
[D] (in)
Wire Size
AWG
Fork Lug
Ring Lug
Copper Lug
TRM0
Copper Lug
TRM6
0.45 (11.4)
#8 (0.168)
0.45 (11.4)
#8 (0.168)
6-0
14-6
The Elevator Screw option allows the
screw and clamp to be raised out of the
mating threads completely. This provides
for the insertion and use of a ring or lug
type wire terminal. Refer to TABLE 1 for
Compatible Terminals.
Page 5
Copyright © 2018 Sensata Technologies, Inc.
www.sensata.com
京公网安备 11010802033920号
EEWORLD
