Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
[font=宋体][size=4] When debugging lan8720 hardware, you need to check whether the ground pad is cold soldered, whether the internal voltage regulator 1.2V has output, and whether it has output 50M freq...
I used STM32 to write a matrix keyboard program. It was originally a query method, but now it has been changed to a timer method.Schematic diagram:void KEY_Init(void){GPIO_InitTypeDef GPIO_InitStructu...
1. Interrupt nesting, the control bit of the priority430 general interrupt is the GIE bit in the status register (this bit is in the SR register). When this bit is in the reset state, all maskable int...
[size=4]1. Not familiar with the internal structure of FPGA and the basic principles of programmable logic devices. Why is FPGA programmable? I am afraid that many novices do not know, and they do not...
Transmit power is the main technical indicator of radio transmission equipment and one of the technical indicators that radio management departments need to test. This article mainly introduces severa...
While I was working hard on ucLinux, I also became interested in embedded real-time operating systems. The first real-time operating system I came into contact with was uC/OSⅡ. At that time, I started...
The inverter is an important part of the emergency power supply. In order to achieve timely adjustment of the inverter output AC voltage in the emergency power supply, reduce the output voltage harmo...[Details]
The operation of a three-phase motor requires a three-phase inverter, which generally consists of: 6 power transistors (MOSFETs or IGBTs), gate drivers (one or more) to control the transistors, and c...[Details]
With the recent surge in world oil prices, energy costs have become a concern. On average, buildings account for 40% of total CO2 emissions, and according to Energy Star, 50% of residential en...[Details]
Today I will tell you about the serial communication of this board. Here we don't need to look at the board, as long as we know how to use the serial port of the 51 chip. Let's go directly to the c...[Details]
In order for the code to be recognized by Doxygen, it must follow Doxygen's writing rules. Comments must start with / and end with */.
1. Add Type
1. Add the homepage (mainpage):
Format:
/
...[Details]
The big guys are all getting into pig farming. What are they planning? Is Huawei also going to raise pigs? Recently, Ren Zhengfei publicly mentioned Huawei's "Nanniwan" plan for the first time...[Details]
Abstract: Aiming at the typical design of dual configuration of microcomputer transformer protection, the purpose, wiring method and setting principle of each protection configuration are describe...[Details]
As a local advanced automotive electronic system supplier, Jingwei Hirain also has rich R&D and production experience in the field of automotive powertrain. At present, the company has launched thr...[Details]
Recently, MediaTek released a series of Dimensity Auto cockpit platform system-on-chips combined with AI technology at the NVIDIA GTC conference, including CX-1, CY-1, CM-1 and CV-1. All four produ...[Details]
Wayve, founded by a team from the Department of Engineering at the University of Cambridge, uses machine learning algorithms to enable self-driving cars to drive on unfamiliar roads using only camera...[Details]
Semiconductor laser tubes (LDs) and ordinary diodes use different processes, but their voltage and current characteristics are basically the same. At the operating point, small voltage changes will c...[Details]
【Main content】
1. Industry Overview
Definition of drive-by-wire chassis: A chassis that uses electrical signals instead of mechanical devices to achieve precise control of the...[Details]
1 Introduction The DMX512 protocol is a digital multiplexing protocol developed by the United-States Institute for Theater Technology (USITT). Its original intention was to make the numerous dimmers ...[Details]
On March 28,
the official microblog of
CATL
(300750.SZ) released a message "Welcome new students" saying that the Shenxing
battery
and Kirin battery all-round series were officially ...[Details]
The STM8L series MCU is a low-power MCU launched by ST. Compared with the STM8S series, the power consumption is much lower, but the internal structure is also much reduced. Be sure to read the manu...[Details]