The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts absorb on the top
tapes to cause a failure in the mounting and the parts are destructed by static electricity (more than 1kV : 1J, 2A, 2B, 2E 0.5kV : 1E, Human Body Model 100pF 1.5kΩ) to change the
resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged on the tapes. Similarly, care should be given not to apply the
excessive static electricity when mounting on the boards.
●
Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc. The flux may
contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na
＋
), chrorine (Cl
−
) etc. Therefore these kinds of ionic substances may
induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since lead free solder contains ionic substances.
Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk may happen that
the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of protecting coat may be dropped down.
Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling strength. 5∼
35℃/35∼75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like hydrogen sulfide, sulfurous acid
gas, hydrogen chloride, etc. may drop solderability.
Currently, China's automobile industry is in a period of rapid growth, and consumers' requirements for vehicle quality are also increasing, such as vehicle safety, entertainment, comfort, etc., which ...
It is always easy to be confused when reading the PDF document of the chip. To summarize, by looking at the timing diagram, you can understand whether the data is read and written on the rising edge o...
For example, through the half-bridge method, a DC voltage of 40V is passed through a step-up transformer and an 8-fold voltage doubler rectifier circuit to generate 40KV/50W.
So how should this step-u...
I used STM32F767 to make a test machine, and I needed a network port. I bought a development board, and the network port example in the routine required knowing the computer's IP address. My boss said...
In the previous article , the compiled hello word program could not run on the board. In this article, we will recompile a system image by ourselves, and then put the compiled hello word program into ...
challenge:
Reduce characterization time for increasingly complex wireless power amplifiers (PAs) without sacrificing measurement accuracy or increasing equipment cost.
Solution:
Usin...[Details]
1. Project Overview 1.1 Introduction A greenhouse is a place that can change the growth environment of plants, create optimal conditions for plant growth, and avoid the influence of seasonal chan...[Details]
Beginner's guide to PIC microcontrollers - memory
The memory can be divided into two types: data memory (RAM) and program register (ROM or EEPROM).
It is the computer's memory device, whi...[Details]
Edge Intelligence X Embedded Innovation Lights Up Digital China 2021 Advantech Embedded Design Forum concluded successfully! Shenzhen, May 27, 2021. Advantech Technology (stock code: 2395), a glob...[Details]
1. Ground resistance test requirements:
a. For AC working grounding, the grounding resistance should not be greater than 4Ω;
b. For safety working grounding, the grounding resistance should not ...[Details]
There is a connection problem between the 5V 51 microcontroller and the NRF24L01 wireless module. They said that improper connection will cause the following problems: 1. The power supply voltage of ...[Details]
Real-time online environmental monitoring system based on MCS-51 single chip microcomputer
1 Introduction
The data collector based on GPRS and MCS-51 single-chip microcomputer is a real-time...[Details]
During the production process of lithium batteries, the cells need to be formed and divided into different capacities to ensure the quality of the final power products. This article mainly mentions...[Details]
Schematic diagram of L297, L298 driving stepper motor, tested and available The 51 single-chip microcomputer program for L297 and L298 to drive the stepper motor is as follows: #include "AT89X51.h"...[Details]
The portable megohmmeter circuit is shown in the figure. IC1 is a six-Schmitt trigger CD40106, in which trigger 1 constitutes an oscillation circuit, and triggers 2 and 3 constitute a driving circuit....[Details]
It is reported that Huawei and GAC Aion, a new energy vehicle company under GAC Group, have started to jointly develop the next generation of smart electric vehicles. Both parties will invest a lot o...[Details]
In the operation of automotive ECU software, software code operation security is the first priority. Try not to have flash_erase and flash_write operations in the code. This is mainly to prevent the ...[Details]
An Overview of Non-Isolated Buck Power Supply Design Methodology
Non-isolated buck power supply is a commonly used power supply structure, accounting for more than 90% of fluorescent lamp ...[Details]
As product complexity and density increase and design cycles continue to shrink, addressing electromagnetic compatibility (EMC) issues late in the design cycle becomes increasingly impractical. At ...[Details]
In the header file "stm32f10x.h": #define HSE_Value ((uint32_t)8000000) /! Value of the External oscillator in Hz/ The italic content defaults to 8000000. When you modify the external crystal oscil...[Details]
Download Centre
京公网安备 11010802033920号
EEWORLD
