Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
A batch of fpga core boards are released. There are two companies, ALTERA and XILINX, to choose from!
The workmanship is very good, all of them are industrial-grade mass-produced, there are boards for...
[i=s]This post was last edited by jinglixixi on 2020-9-13 08:56[/i]The development board is equipped with an I2C interface, but unfortunately it is inconsistent with the pin arrangement of the OLED sc...
I would like to ask about the VCE saturation voltage drop protection and current protection of the A316J optocoupler. Are the output levels of the fault pins the same?...
It has been a long time since my last post. I have been busy with work so I have slowed down my study progress. I will try to share my study status and experience in more detail in the future.
I bough...
Introduction: As design complexity increases, the traditional development model based on text specifications can no longer meet the portability requirements of SDR hardware and software. This article ...
CMOS integrated circuit circuit that can directly drive the relay to work
In the habit of electronic enthusiasts to understand circuit knowledge, they always think that CMOS integrated circu...[Details]
In recent years, with
the growth of production and sales of
new energy vehicles
, the market demand for DC/DC converters has continued to rise. DC/DC converters
play a very important role i...[Details]
Composite image of CIMON on board the International Space Station (ISS). (Credit: DLR/T.Bourry/ESA) Face and voice design The ability to maintain eye contact and communicate is a ba...[Details]
A digital voltmeter is designed using the single-chip microcomputer AT89S51 and ADC0809. It can measure DC voltage values between 0 and 5V and display four digits, but requires the minimum number o...[Details]
Today, the official released a summary of answers from the head of MIUI on-line about the interaction between mobile phones and computers, whether the video toolbox will be adapted to existing models...[Details]
A multimeter can measure a variety of electrical quantities. Although its accuracy is not high, it is easy to use and carry, and is particularly suitable for checking circuits and repairing electric...[Details]
Because the light emitted by most light sources is collectively called white light, the color temperature or correlated color temperature of the light source is used to refer to the relative whitenes...[Details]
The 1960s and early 1970s are considered the "muscle car" era. This began with the introduction of large engines into mid-range car designs. The most famous examples include Chevelles, Fairlanes, G...[Details]
(TIA/EIA568A) defines the following sequence:
copper sheet upward, wire at the bottom, count from left to right: 12345678 indicates the position,
1- orange and white--------...[Details]
Figure 1 is a block diagram of a resistor production test system based on a 2400 digital source meter, which is used to continuously feed resistors and calibrate them.
Figure 1
Resistor Produ...[Details]
According to MEMS Consulting, Sony
Semiconductor
Solutions
(hereinafter referred to as "SSS") recently launched a new CMOS
image sensor
for automotive cameras
:
IMX735, which...[Details]
Huawei's US research arm Futurewei began laying off employees on Monday, Reuters reported. One employee, who declined to be named, told Reuters he had been fired and needed to leave the office by n...[Details]
MediaTek today (November 19) released the world's first smartphone processor Dimensity 9000 using TSMC's 4nm process. The chip also set many industry firsts. The CPU part of Dimensity 9000 adopts ...[Details]
On May 19, the Jiangxi Zhaochi Optoelectronics headquarters and new packaging production line expansion project with a total investment of 7 billion yuan was signed and settled in Qingshan Lake Distr...[Details]
A soft starter is a power electronic device used for motor starting. It can effectively reduce the current shock during starting, thereby protecting the motor and the power grid. However, in some c...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
