Axial Leaded Precision Resistors
Type HOLCO Series
Key Features
Ultra-Precision
- Down To
0.05%
Low TCR
–
Down To
5ppm/°C
Long Term
Stability
Up To 1 Watt
At 70°C
The Holco range of Precision Metal Film Resistors meets the requirement for
economically priced components for industrial and military applications. The
manufacturing facility utilises closely controlled production processes including
the sputter coating of metal alloy films to ceramic substrates, and laser spiralling
to achieve close tolerance and high stability resistors. An epoxy coating is
applied for environmental and mechanical protection. Commercially the Series is
available in two case sizes, from 1 ohm to 4M ohms, tolerances from 0.05% to
1% and TCR's from 5ppm/°C to 100ppm/°C.
Characteristics
–
Electrical
H4P
Power rating @70°C 1W
Temperature Rise
70°C
Limiting Element
500v
Voltage
H4
0.5W
55°C
350v
H8
0.25W
40°C
350v
General Data
Lead Material
Encapsulation
Resistor Marking
Solvent Resistance
Solderability to BS CECC 40101 004 Para 4.15.1
Conformal Epoxy Coating
Legend printed in accordance with CECC 40000 Para 2.4
The epoxy coating and print will withstand the action of all
commonly used industrial cleansing solvents
1773230 Rev. H 03/2019
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
Axial Leaded Precision Resistors
Resistance Range by TCR and Tolerance
TCR
Ppm/°C
5
10
15
25
50
100
0.05%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
1M0
10R
–
1M0
10R
–
1M0
H4P
0.1% -
0.25%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
2M0
10R
–
2M0
10R
–
2M0
0.5% -
1.0%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
2M0
10R
–
4M0
10R
–
4M0
0.05%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
1M0
10R
–
1M0
10R
–
1M0
H4
0.1% -
0.25%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
2M0
10R
–
2M0
10R
–
2M0
0.5% -
1.0%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
2M0
10R
–
4M0
10R
–
4M0
0.05%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
1M0
10R
–
1M0
10R
–
1M0
H8
0.1% -
0.25%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
2M0
10R
–
2M0
10R
–
2M0
0.5% -
1.0%
10R-
500K
10R
–
1M0
10R
–
1M0
10R
–
2M0
10R
–
4M0
10R
–
4M0
Performance Characteristics
Voltage Coefficient of
Resistance (Between 10%
and Full Rated Voltage)
Insulation Resistance at 500
Volts
Resistance to Soldering Heat
(260°C for 10 Secs.)
Short Term Overload
(6.25 Times Rated Wattage
for 5 Seconds)
Ambient Temperature Range
Rapid Change of
Temperature
(-55°C to +155°C, 5 cycles)
Shelf Life (at Normal Room
Temp.)
Vibration
(10-500 HZ Amplitude
0.75mm, or Acceleration
98m/s2 whichever is less
severe, sweep duration 6
hours)
Vibration
(55-2000 Hz Simple
Harmonic Motion, Max.
Acceleration 98m/s2,
Duration 35±5 Minutes)
Bump (390m/s2, 4000
Bumps)
Load Stability
Damp Heat Steady State
Typical Data
Less Than 5ppm/Volt Applied
Reference
N/A
Greater Than 10¹² Ohms
Less Than 0.05%
Less Than 0.06%
N/A
BS CECC 40101 004 Para
4.15.2
BS CECC 40101 004 Para 4.11
-55°C to +155°C
Less Than 0.04%
BS CECC 40101 004
BS CECC 40101 004 Para 4.16
Less Than 0.05% Per Annum
Less Than 0.04%
N/A
BS CECC 40101 004 Para 4.19
Less Than 0.04%
MIL STD 202
METHOD 204-C
Less Than 0.03%
See graph
See Graph
BS 2011 Part 2.1 Eb 1977
(1984)
N/A
BS CECC 40101 004
Para 4.21
1773230 Rev. H 03/2019
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
Axial Leaded Precision Resistors
Dimensions
H4P
H4
H8
Body Length (L) maximum:
10.50mm
10.50mm
7.20mm
Body Diameter (D) maximum:
3.70mm
3.70mm
2.70mm
Lead Diameter (d) maximum:
0.60mm
0.60mm
0.60mm
Lead Length (l) nominal:
30.0mm
30.0mm
30.0mm
Recommended Mounting Pitch:
12.70mm
12.70mm
10.2mm
Weight (g/100 resistors)
40
40
24
N.B. To prevent damage to the components conformal coating, the leads should be adequately
supported during the forming process
Long Term Stability
1773230 Rev. H 03/2019
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
Axial Leaded Precision Resistors
Derating
How To Order
H8
Common Part
H4P
H4
H8
100R
Resistance
Value
1.0Ω- 1R0
10Ω - 10R
1KΩ (1000
Ohms)- 1K0
10KΩ (10,000
ohms)
–
10K
B
Tolerance
A
–
0.05%
B
–
0.1%
C
–
0.25%
D
–
0.5%
F
–
1.0%
Y
TCR Code
A
–
5ppm
B
–
10ppm
Y
–
15ppm
D
–
25ppm
C
–
50ppm
Z
–
100ppm
A
Release
A
–
Part can
only be sold
with
commercial or
C of C release
1773230 Rev. H 03/2019
Dimensions in
millimetres unless
otherwise specified
Dimensions Shown for
reference purposes only.
Specifications subject to
change
For Email, phone or live chat,
go to: www.te.com/help
京公网安备 11010802033920号
EEWORLD
