EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8ALF-01-6731-C-D

Description
Array/Network Resistor, Isolated, Thin Film, 1.2W, 6730ohm, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

GUB-GM8ALF-01-6731-C-D Overview

Array/Network Resistor, Isolated, Thin Film, 1.2W, 6730ohm, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT

GUB-GM8ALF-01-6731-C-D Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1076343009
package instructionSMT, 2244
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.5
Other featuresULTRA PRECISION
structureMolded
Component power consumption0.16 W
The first element resistor6730 Ω
JESD-609 codee3
Manufacturer's serial numberGUB
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width5.588 mm
Rated power dissipation(P)1.2 W
Rated temperature70 °C
resistance6730 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code2244
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeGULL WING
Tolerance0.25%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
SensorTile.Box Kit Operation Mode Expert Mode Trial
# SensorTile.Box Kit Operation Mode Expert Mode Trial# Expert Mode According to the guidance of the "SensorTileBox_2_Expert Mode Introduction.pdf" file in the resource post, it is easy to complete the...
lvqy ST MEMS Sensor Creative Design Competition
Boost chip
I would like to ask about the boost chip TPS61021A. When powered by a battery, the initial battery voltage is 3.6V. As the battery power decreases, the voltage changes to 2V, while the output is a sta...
goujunquan TI Technology Forum
An impedance matching problem of rf amp
[i=s] This post was last edited by learntest on 2019-4-15 12:25 [/i]Where does he get this 26mV? ? 26mV should be the voltage of VE, right? Because re=26mV/ie, but why is ve 1.2v? 81*(26mv/ie)=50 ohms...
learntest Analog electronics
Nanxin, Qinheng, Zhaoyi, Yatli...many good boards are free to review here!
For those who love boards, it is a happy thing to see a good board for free evaluation. Now, I want to tell you that there are many good board evaluation activities online in the forum recently. Will ...
okhxyyo Domestic Chip Exchange
OHM-Illustrated Introduction to Electrical Engineering
Hello, everyone: Today I shared the introductory material on electrical engineering that I learned, "OHM-Illustrated Introduction to Electrical Engineering" by OHM of Japan. This book explains the bas...
dahui2010 Industrial Control Electronics
Is there something wrong with my op amp circuit?
1. Given a fixed value of V1: 0.5V, the value of v2 is adjustable. 2.When 0.5V<V2<1V (approximately this value, there may be some difference above or below), the OUT output is my ideal output value.Qu...
吹个大气球 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号