Features ....................................................................................................................................................................................... 1
Typical Phase Jitter (70 fs RMS) and Phase Noise Data ............................................................................................................. 2
Ordering Information .................................................................................................................................................................... 3
LVPECL and FlexSwing Termination .................................................................................................................................. 19
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 20
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 20
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V .................... 20
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 21
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 22
Dimensions and Patterns ― 3.2 x 2.5 mm x mm ....................................................................................................................... 23
Revision History ......................................................................................................................................................................... 24
Rev 0.54
Page 4 of 25
www.sitime.com
SiT9501
Ultra-low Jitter Differential XO for Standard Networking Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Symbol
f
Min.
Typ.
Max.
Unit
MHz
Condition
Refer to frequencies listed in
Error! Not a valid result for table.
s
ection.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 6
and
Figure 8
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 13
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 14
12 kHz to 20 MHz offset frequency integration bandwidth
From Silicon Valley startups to established German OEMs, to drivers and avid car enthusiasts around the world, everyone is wondering what the future of connected cars will look like. How will it chang...
Live playback: The most important component of the analog world - Signal chain and power supply: USB Type-C? PD special session : https://training.eeworld.com.cn/course/67746...
I would like to ask, when using CC2541 to connect a Bluetooth module, is it easier to program CC2541 as a host or as a slave?What about programming? Thanks!...
Previously, we built the Matter firmware and chip-tool. Next, we need to establish a Thread network and configure the network through BLE so that we can control the Matter device through chip-tool.1 E...
The new version also introduces the new DeepPRIME noise reduction tool, which is 4 times faster than the previous version and supports Fujifilm X-Trans sensors (Beta) DxO PhotoLab now sets the stan...[Details]
The first circuit principle: The AC220V voltage is half-wave rectified by D3 and filtered by C1 to obtain a voltage of about +300V. One path is added to the switch tube Q2 c pole through the pri...[Details]
The 2016 China International Solar Power Expo was held in Beijing from March 29 to 31. Taking advantage of this exhibition, Sungrow launched its new 50kW string inverter SG50KTL to the world.
...[Details]
0 Preface
In process control, since the industrial site is very scattered, there are many I/O points, and the working environment of various instruments is very harsh, it is obviously not advisable t...[Details]
1 Introduction EEPROM is a memory with power-off memory function. Its content can be rewritten like ordinary RAM, and it can automatically erase and replace it with new content when rewriting. It d...[Details]
Huabei announced the official launch of the "Spring Festival Travel Interest-Free Installment Plan". After users search for "Spring Festival Travel" on Alipay to receive Huabei's interest-free instal...[Details]
According to Jiwei.com news, the Shanghai Regulatory Bureau recently disclosed the basic information table of the coaching filing of Shanghai Canrui Technology Co., Ltd. (hereinafter referred to as: ...[Details]
This article uses the following environment: Computer: Windows 10 Main control: W806 (240MHZ) Peripheral acquisition: INA226 (IIC) Peripheral display: 0.91 OLED (IIC) Compilation environment: Pingtou...[Details]
The main factors affecting resistance or resistivity testing are:
a. Ambient temperature and humidity
The resistance value of general materials decreases with the increase of ambient temp...[Details]
The general PCB design process is as follows: preliminary preparation - PCB structure design - PCB layout - wiring - wiring optimization and silk screen - network and DRC inspection and structure i...[Details]
According to foreign media reports, the demand for high-performance energy storage systems from emerging technologies such as electric vehicles and artificial intelligence is growing, which has prom...[Details]
According to Reuters, the Trump administration is preparing to add Semiconductor Manufacturing International Corporation (SMIC) and China National Offshore Oil Corporation (CNOOC) to the blacklist, t...[Details]
New progress has been made in the research of high-performance polymer thermoelectric materials. On the 25th, the reporter learned from the Institute of Chemistry of the Chinese Academy of Sciences...[Details]
Recently, a bricklaying robot
called Hadrian X
has attracted everyone's attention again. It can build a wall the size of a tennis court in 4 hours. The robot looks like an ordinary truck, bu...[Details]
Li Auto and Mercedes-Benz to use Snapdragon Extreme Automotive Platform in their future production models
New Snapdragon Cockpit Extreme and Snapdragon Ride Extreme platforms debu...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
