Standard Frequencies – see Page 5 for developed frequencies.
* Check with factory for availability of frequencies not listed.
Applications
Automotive Electronics
Mobile Multimedia/Infotainment
Car Navigation Systems
Internet of Things [IoT, IIot]
Microcontrollers and FPGAs
Wireless Communication
Ethernet/GbE/SyncE
Medical Electronics
Commercial Military & Aerospace
Description
CTS Model SA532 incorporates a low cost, high Q, small size quartz resonator specifically developed to operate
over extended temperature ranges for use in automotive electronics.
Ordering Information
Model
SA532
Frequency Code
[MHz]
XXX or XXXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
5
Temperature
Range
G
Load
Capacitance
A
Packaging
T
Code
Frequency
Product Frequency Code
1
Code
1
X
2
3
5
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
±50ppm
Code
I
G
H
N
P
M
Code
X
2
3
5
6
7
Stability
±15ppm
±20ppm
±30ppm
±50ppm
±100ppm
±150ppm
Temp. Range
-40°C to +85°C
2
-40°C to +105°C
3
-40°C to +125°C
4
-40°C to +150°C
5
-55°C to +105°C
5
-55°C to +125°C
5
Packing
Code
1k pcs./reel
T
Code
F
T
Mode
Fundamental
3rd Overtone
Code Capacitance Code Capacitance
7pF
16pF
V
C
8pF
18pF
K
D
9pF
20pF
E
J
10pF
24pF
A
F
12pF
30pF
L
G
13pF
Series
B
S
Notes:
1]
2]
3]
4]
5]
Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
Available with all stability codes.
Available with stability codes 3, 5, 6 and 7.
Available with stability codes 5, 6 and 7.
Stability codes 6 and 7. Contact factory for code 5 availability.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
Today, there is news that Cisco's RD department in Shanghai has laid off employees. There is also a clarification that it is a department in Shanghai that was laid off because the product of outdoor f...
1. Prepare the design platform environment
Use the ULINK2 emulator to connect the JTAG interface of the motherboard of the EduKit-IV experimental design platform; use the cross serial cable that comes...
Download MM32F013x_Lib_Samples_V1.02 from the official website http://www.mm32mcu.com/ to get the corresponding routines; download MindMotion.MM32F0130_DFP.1.0.1.pack to provide chip support, use MM32...
A few days ago, I posted about 27MHZ frequency measurement. Forum friends were very enthusiastic and gave various solutions. After checking the parameters, I found a problem: the period corresponding ...
[i=s]This post was last edited by nanasong on 2022-8-4 16:18[/i]Could you please tell me what is the use of the series resistor between the input and output of the inverter? The input signal is a 100M...
Follower circuit:The sampling voltage VI_AMP_IN on the front-stage sampling resistor is sent to the ADC for A/D conversion through the follower action VI_AMP_OUT of U6.The role of U6 here is to reduce...