ECONOLINE - DC/DC-Converter
RS Series, 2 Watt, SIP8, Regulated, Isolated (Single Output)
Features
●
●
●
●
2:1 Wide Range Voltage Input
1kVDC Isolation
Efficiency to 83%
UL 94V-0 Package Material
●
●
0.05% Line Regulation
Continuous Short Circiut Protection
with Current Foldback
●
Low Noise
Selection Guide
Part Number
SIP8
RS-0505
RS-0509
RS-0512
RS-0515
RS-1205
RS-1209
RS-1212
RS-1215
RS-2405
RS-2409
RS-2412
RS-2415
RS-4805
RS-4809
RS-4812
RS-4815
Input
Voltage Range
(VDC)
5-9
5-9
5-9
5-9
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
Rated Output
Voltage
(VDC)
5
9
12
15
5
9
12
15
5
9
12
15
5
9
12
15
Output Current
at Full Load
(mA)
400
222
167
133
400
222
167
133
400
222
167
133
400
222
167
133
SIP8
Package
Style
Capacitance
Cin
Cout
5-9V, 9-18V & 18-36V input types
36V -72V input types
36V-72V input types
10µF, 50V
10µF, 100V
100µF, 25V
www.recom-international.com
August 2002
EC 61
ECONOLINE - DC/DC-Converter
RS Series, 2 Watt, SIP8, Regulated, Isolated (Single Output)
Electrical Specifications
(measured at T
A
= 25°C, at nominal input voltage and rated output current unless otherwise specified)
Input Voltage Range
Output Accuracy
Rated Power
Isolation Voltage
Ripple & Noise (B/W = 20MHz)
Line Regulation
Load Regulation (10% to 100% Load)
Switching Frequency at Full Load
Short Circuit Protection
Operating Temperature Range
Storage Temperature Range
Efficiency
2:1
±1% typ.
2 W max.
1kVDC
Output Power (Watts)
1.5
1.0
Safe Operating Area
0.5
0
-40
0
50
100
125
150
80
Operating Temperature ˚C
2.0
50mV p-p max.
±0.2% max.
±0,5% typ.
85kHz min.
Continuous
–40°C to +80°C (see graph)
–50°C to +125°C
up to 83%
Package Style and Pinning (mm)
8 Pin SIP Package Style
C
in
0.25±0.05
2.0±0.50
1 2 3
5 6 7 8
3.20 typ.
C
out
All RS-XXXX types 10uF, 100V
Philips Part No. 15162109
100uF, 25V
Philips Part No. 13556101
Recommended Footprint Details
2.54
21.80 max.
9.20 max.
1.0ø+0.15/–0
2.54
Pin 3 (CTRL)
This pin provides an Off function which puts
the converter into a low power mode. When
the pin is ‘high’ the converter is OFF and
when the pin is high ‘Z’ the converter is ON.
There is no allowed low state for this pin.
Voltage to be applied via a limiting resistor
with a recommended value of 1K for RS-
05xx; 3.3K for RS-12xx; RS-24xx and 10K
for RS-48xx)
Pin 5 (NE)
This pin is used internally and must have no
external connection.
Pin 8 (Cs)
This pin provides a connection point to the
main reservoir capacitor. Additional capaci-
tance can be added from this to pin 7. Any
low esr capacitor will improve ripple and
noise in some measure. The benefit of this
access point over simple additional output
filter inductor. Maximum values of external
capacitance will be depend on the output
voltage/loading of the converter and the
desired ripple figure. Starting values can be
in the range of 100uF.
Control Pin Input Current:
11.10 max.
3.10min.
0.50±0.05
2.54 typ.
RS-0505
RECOM
****
10mA
0.50±0.05
Voltage Set Point Accuracy
with external input/output
capacitors refer to
recommended test circuit:
Control Pin (CTRL) Input
Current, control voltage
applied via 1K resistor,
output voltage must
reduce to 0V:
typ. ± 1%
max. ±2%
Pin Connections
Pin # Single Description
1
2
3
4
5
6
7
8
NE
+Vout
OVout
CS
GND
+Vin
CTRL
Negative input
Positive input
Control input
(can be left open)
Not fitted
No exernal connection
allowed
Positive output
Negative output
Optional external capacitor
typ. 3mA
max. 6mA
External capacitance
Although these converter will work without
external capacitors, they are necessary in
order to guarantee the full parametric per-
formance over the full line load range. All
parts have been tested and characterised
using the following recommended values
and test circuit.
D
2
C
5
C
6
C
S
Pin 8
L
1
V
+
O
+
Pin 7 0V–
External
Cap.
EC 62
August 2002
www.recom-international.com
京公网安备 11010802033920号
EEWORLD
