EEWORLDEEWORLDEEWORLD

Part Number

Search

6062-X-A92-0D-2

Description
10/15A, 250VAC, MALE, MAINS POWER CONNECTOR, SOLDER, ROHS COMPLIANT
CategoryThe connector    The connector   
File Size398KB,3 Pages
ManufacturerSCHURTER
Websitehttp://www.schurterinc.com/
Download Datasheet Parametric View All

6062-X-A92-0D-2 Overview

10/15A, 250VAC, MALE, MAINS POWER CONNECTOR, SOLDER, ROHS COMPLIANT

6062-X-A92-0D-2 Parametric

Parameter NameAttribute value
Objectid1212896405
package instructionROHS COMPLIANT
Reach Compliance Codeunknown
Other featuresSTANDARDS: IEC/EN 60320-1/C14, UL 498; UL 94V-0, CSA C22.2, VDE, QUICK CONNECT
Connector typeMAINS POWER CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedNOT SPECIFIED
Contact point genderMALE
Coupling typeSNAP
DIN complianceNO
IEC complianceYES
MIL complianceNO
Power Connector Ratings10/15A, 250VAC
Manufacturer's serial number6062
Plug informationMULTIPLE MATING PARTS AVAILABLE
Installation typePANEL
OptionsGENERAL PURPOSE
Shell materialPA6
Termination typeSOLDER
Total number of contacts3
Connectors (Inlets/Outlets)
www.schurter.com/pg07
IEC Appliance Inlet C14, Screw-on Mounting, Front Side, Solder or Quick-connect or Screw Terminal
6062
C14
70° C
Description
- Panel Mount:
Screw-on mounting, Frontside
- Appliance Inlet, Pin temperature 70 °C, Protection class I
- Solder, Quick Connect or Screw Terminals
References
Weblinks
We recommend for new applications the type 8843.FLR
pdf, html, General Product Information, Approvals, RoHS, CHINA-RoHS,
Mating Connectors, e-Store, SCHURTER-Stock-Check, Distributor-
Stock-Check, Accessories
Approvals
- VDE Certificate Number: 40011871
- UL File Number: E96454
- CSA File Number: 27324
Newly available variants corresponding to V-Lock mating cordset. The connector is equipped with a notch intended for use with the latching cordset.
The cord latching system prevents against accidental removal of the cordset.
Technical Data
Ratings IEC
Ratings UL/CSA
Dielectric Strength
10 A / 250 VAC; 50 Hz
15 A / 250 VAC; 60 Hz
> 3 kVAC between L-N
> 1.5 kVAC between L/N-PE
(1 min/50 Hz)
-25 °C to 70 °C
from front side IP 20 acc. to IEC 60529
Suitable for appliances with protection
class 2 acc. to IEC 61140
Solder, Quick Connect or Screw Ter-
minals
PA6, black / grey / white, UL 94V-0
Appliance Inlet
C14 acc. to IEC/EN 60320-1
UL 498, CSA C22.2 no. 42 (for cold
conditions) pin-temperature 70 °C, 10 A,
Protection Class 1
Allowable Operation Temp.
Degree of Protection
Protection Class
Terminal
Material: Housing
Dimensions
30
21.5
41 mm
19.5
- 0
19.3
22.5
+0.2
R
3
41
3.
2
32
16.5
26.9
3
ø
27.2
- 0
+0.2
Length of the terminal please find at the order code configuration table
Connectors
32

Choosing the Correct Thermistor for Your Temperature Sensor
[i=s]This post was last edited by qwqwqw2088 on 2020-5-7 08:44[/i]When faced with thousands of thermistor types, selecting the right one can be quite overwhelming. Here are some of the important param...
qwqwqw2088 Analogue and Mixed Signal
How to fix the program to FLASH in C6455 DSK of DSP C6000 series
[size=4]1. Experimental platform[/size] [size=4] 1.1. Hardware platform[/size] [size=4] TMS320C6455 DSK development board, USB cable, etc. [/size] [size=4] [/size] [size=4] 1.2. Software platform[/siz...
Jacktang DSP and ARM Processors
EEprom write speed is slow
I'm using an atmel chip recently. Its internal eeprom writes data very quickly for the first time, but becomes very slow to write data to the same location afterwards. It takes about 8s to write 5K da...
zhuzd Embedded System
CircuitPython 7.0.0 released
Notable additions to 7.0.0 since 6.3.0Support for the CircuitPython development workflow over BLE. Camera support on ESP32S2. qrio: QR code decoding. The keypad key-scanning module. Run-time customiza...
dcexpert MicroPython Open Source section
They are all six non-gates. This power supply can be used even if it is connected reversely, but it cannot be replaced.
RT, I'd like to share a board made by my dad's company. At the beginning of the development, they used a part that they had some stock on hand. Motorola's six-NOT gate chip was finished, but it was di...
小潜艇 PCB Design
PCB layout
Is it necessary to place copper between pairs of differential lines on a double-sided board to isolate crosstalk? Do I still need to place copper if the spacing between several sets of differential li...
asionl PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号