Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[i=s]This post was last edited by emmnn on 2022-1-29 11:10[/i]Preface
It has been more than two weeks since my last post. I just got home and rested for two days. I remembered the review and took out ...
FPGA basics and how it works
Whether you use a graphical design program, ANSI C or VHDL, such a complex synthesis process can make you wonder how FPGAs really work. How do the programs in this chip wo...
[i=s]This post was last edited by DIAG on 2019-3-24 22:01[/i] [size=5]It’s still the old 32 Skyworth LCD TV, with simple functions, suitable for my grandma. The auxiliary 5V power supply was repaired ...
The difference and usage of passive crystal and active crystal oscillator :This content is originally created by EEWORLD forum userzkj2014. If you need to reprint or use it for commercial purposes, yo...
The title of this chip in the review is: Ateli AT-START-F425, the first choice for USB and CAN applications
Now let's start the basic use of CAN:
1. Add can.h and can.c to the drivers folder:
The RX o...
TrendForce said that the rapid increase in the penetration rate of the global new energy vehicle market has stimulated the annual increase in the installed capacity of power batteries. At the same tim...[Details]
1. Introduction
In the 21st century, the global energy shortage and the call for energy conservation are getting louder and louder. Advanced energy-saving technology has gradually become a bri...[Details]
IT Home reported on September 12 that according to a contribution from IT Home netizen @戈多-Godo, Apple today pushed the watchOS 8 public beta version Beta 7, which is 174MB in size. There i...[Details]
introduction
As people's enthusiasm for open source software grows, Linux, as a powerful and stable open source operating system, is increasingly favored by thousands of computer experts and e...[Details]
The concept and working principle of servo drive
A servo drive is an electronic device that controls the rotation of a servo motor by providing appropriate signals to it, thereby achieving pre...[Details]
1. Principle To make your own system call, of course, all you need to do is understand the system call process: Let's take the open function as an example: when the user space executes the open funct...[Details]
0 Introduction
SNMP (Simple Network Management Protocol) is widely used and powerful. As long as the management software has MIB (Management Information Base) and has appropriate permissions,...[Details]
On February 3, the topping-out ceremony of the test complex building of Sanan Optoelectronics Display Industrialization Project (Phase I) located in Gedian, Hubei Province was held. In July 2019, S...[Details]
During the period between the Lesser Heat and the End of Heat, the temperature is the highest, and the weather is humid and hot, which is what we often call the "dog days". Beijing is experiencing ...[Details]
Wireless Sensor Network (WSN) is a multi-hop self-organizing network system composed of a large number of sensor nodes through wireless communication. Wireless sensor nodes can transmit sensor info...[Details]
The iPhone 12 Pro is equipped with a 6.1-inch Super Retina XDR screen with a resolution of 2532 x 1170, a 2000000:1 contrast ratio and a maximum brightness of 1200 nits, which can provide excellent d...[Details]
DDS is the abbreviation of Direct Digital Synthesis (Direct Digital Synthesis) technology. It is a new frequency synthesis technology that has emerged with the rapid development of digital integrated...[Details]
The 23rd China International Industry Fair with the theme of "Carbon Cycle, New Numbers, New Economy" opened at the National Exhibition and Convention Center (Shanghai) on September 19, 2023.
S...[Details]
Sinusoidal excitation signals can generally be generated through oscillation circuits or direct digital frequency synthesizers (DDS). Compared with oscillation circuits, DDS has the advantages of ...[Details]
GD32 MCU
京公网安备 11010802033920号
EEWORLD
