Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
The typical circuit diagram of this chip. I start from the input analysis: after AC input, the half-wave of N is cut off by the diode, and only the half-wave of L can flow in. Then for the two capacit...
Intelligent gas leak alarmAuthor: Blue AngelI got the board in late May and only adjusted the hardware and data collection. I didn't do Bluetooth and aap data upload. Now I will submit the completed p...
蓝色天使onsemi and Avnet IoT Innovation Design Competition
LPS22HH is a high-precision air pressure sensor
24-bit resolution, can distinguish 0.024Pa air pressure changes
The noise can reach 0.65Pa when using the internal filter, which is better than the MPL3...
Is it 100BASE-T1, 1000BASE-T, 100BASE-TX, 10BASE-T or 10BASE-Te? For those who are not well versed in Ethernet physical layer (PHY) terminology, it can be difficult to evaluate the various types of te...
RFID wireless radio frequency identification technology uses radio frequency to exchange data in a non-contact two-way communication to achieve the purpose of identification. Compared with traditional...
Adding a parallel capacitor can turn the LC filter into a π-type filter. If the interference problem becomes more serious, what is the possible reason? How to solve it?...
According to news from Suzhou International Science and Technology Park SISPARK, recently, the first domestic high-end multifunctional flying probe test equipment of iFree (Suzhou) Testing Technology...[Details]
1. System Architecture
The overall working process of the elevator controller is: the elevator is in a waiting state at the first floor. When the user needs to take the elevator, he can press ...[Details]
The PIC series of CMOS microcontrollers developed by Microchip Technology, especially the microcontrollers with built-in second-generation Flash memory, are unique in terms of rapid application. Most...[Details]
The peripheral design of mobile phones is the main method to increase additional functions, selling points and new profits of mobile phones. Hundreds of new mobile phones launched every year are no...[Details]
According to Jiwei.com, due to the large price gap with LCD TVs, OLED TVs have been tepid in the Chinese mainland market and have not seen a large-scale explosion. Recently, the initial price of Xiao...[Details]
The Importance of Logic Analyzer Memory Depth Most modern logic analyzers have a very large bandwidth. For example, the bandwidth of the LAB 6052 logic analyzer from Guangzhou Zhiyuan Electronics Co....[Details]
LED driver power is a power converter that converts power supply into a specific voltage and current to drive LEDs to emit light. Usually, the input of LED driver power includes high-voltage pow...[Details]
According to Jiwei.com, the latest report from market research firm Strategy Analytics shows that by 2021, the smartphone Wi-Fi chip market will reach US$4.3 billion, with Qualcomm, Broadcom and Medi...[Details]
IT Home reported on June 18 that Qualcomm released the Snapdragon 690 processor yesterday, which will bring support for 5G networks to low-priced smartphones. It uses the ARM Cortex-A77 core and...[Details]
ARM processor summary (I)
Introduction to ARM Processor
The ARM processor is a 32-bit reduced instruction set computing (RISC) processor architecture that is widely used in many embedded system des...[Details]
Abstract:
This paper introduces a simple method to implement multitasking mechanism in MCS51 single-chip microcomputer program, and gives source code and an application example. Real-time tas...[Details]
Tian Bo, Chairman and Party Secretary of State Grid Jibei Electric Power Co., Ltd.
Chairman Kou Wei emphasized at the company's video and telephone conference on the deployment of the construc...[Details]
The Korea Institute for Industrial Economics and Trade released a report on July 4 stating that the US government's global supply chain policy may have long-term adverse effects on the South Korean e...[Details]
With the development of digitalization and informatization, large screens have been increasingly used in various occasions, and various display technologies have emerged. From the early CRT to the ...[Details]
1 Virtual Instrument Technology and LabVIEW Virtual instrument technology uses high-performance modular hardware combined with efficient and flexible software to complete various test, measurement an...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
