CTR
www.vishay.com
Vishay Electro-Films
Thin Film, Center-Tapped Resistor Divider Network
FEATURES
•
•
•
•
•
•
•
Wire bondable
Center tap feature
Tight ratio tolerances to: 0.05 %
Chip size: 0.030" x 0.030"
Case: 0303
Resistance range total: 10
to 1 M
Oxidized silicon substrate for good power
dissipation
• Resistor material: Tantalum nitride, self-passivating
• Moisture resistant
• Material categorization: For definitions of compliance
please see
www.vishay.com/doc?99912
I
V
Product may not be to scale
The CTR series is a center-tapped resistor chip combining
excellent stability with 250 mW power levels. The CTR offers
the designer flexibility in use as either a single value resistor
as two resistors with a center tap feature. The CTR’s six
bonding pads allows the user increased layout flexibility.
The CTRs are manufactured using Vishay Electro-Films (EFI)
sophisticated thin film equipment and manufacturing
technology. The CTRs are 100 % electrically tested and
visually inspected to MIL-STD-883.
R
A
R
B
V
I
V
APPLICATIONS
Vishay EFI CTR center-tapped resistor chips are used
mainly in feedback circuits of amplifiers where ratio
matching, high power and tracking between two resistors is
critical.
For low values, the resistance of the six bonding-pad
configurations can vary, depending on the method of
measurement used. Vishay EFI measures low-value
resistors by the four wire Kelvin technique. The method
illustrated above is critical for resistors of less than 100
.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
Tightest Standard Tolerance Available
0.5 %
0.1 %
VALUE
10 to 1M
± 0.1, ± 0.5
± 25, ± 50, ± 100
UNIT
%
ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
10
Ω
25
Ω
100
Ω
360 kΩ 620 kΩ
1 MΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
(1)
Center Tap Ratio,
R
A
/R
B
: Tolerance
Noise, MIL-STD-202, Method 308, < 100
or > 251 k
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at 70 °C (derated to zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Note
(1)
5 ppm/°C for
R
< 100. 20 ppm/°C for
R
< 20
Revision: 25-Feb-13
VALUE
±2
1 ± 1 standard
- 20 typ.
± 0.5 max.
R/R
± 0.2 max. absolute
- 55 to + 150
± 0.1 max.
R/R
± 0.2 max.
R/R
200
12
min.
10
100 max.
0.25 max.
± 0.1 max.
R/R
UNIT
ppm/°C
%
dB
%
%
°C
%
%
V
V
W
%
Document Number: 61020
1
For technical questions, contact:
efi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CTR
www.vishay.com
DIMENSIONS
in inches
0.030
Vishay Electro-Films
R
A
0.026
R
B
0.030
STANDARD CONFIGURATION
Six
locations.
All pads 0.005" x 0.005"
TYPICAL RANGE
10
Ω
to 26.9
Ω
TYPICAL RANGE
27
Ω
to 99
Ω
TYPICAL RANGE
100
Ω
to 1 MΩ
SCHEMATIC
R
T
=
R
A
+
R
B
R
A
R
B
MECHANICAL SPECIFICATIONS
PARAMETER
Chip Size
Chip Thickness
Chip Substrate Material
Resistor Material
Bonding Pad Size
Number of Pads
Pad Material
Backing
VALUE
0.030" x 0.030" ± 0.002" (0.762 mm x 0.762 mm ± 0.05 mm)
0.010" ± 0.002" (0.254 mm ± 0.05 mm)
Oxidized silicon, 10 kÅ minimum SiO
2
Tantalum nitride, self-passivating
0.005" x 0.005" (0.127 mm x 0.127 mm) min.
6
10 kÅ minimum gold
None, lapped
semiconductor silicon
GLOBAL PART NUMBER INFORMATION
Global
Part Number: CTR50000KFKKGNHWS
Global
Part Number Description: CTR 5K 10 %, RT 1 %, 100 ppm/°C, TC track 10, Au, no
back
metal, class H, WS
C
T
R
5
0
0
TOL.
CODE
(%)
B
= 0.1
C
= 0.25
D
= 0.5
F
= 1.0
G
= 2.0
J
= 5.0
K
= 10
M
= 20
0
0
K
F
K
K
G
N
H
W
S
MODEL
CTR
RESISTANCE
RESISTANCE
MULTIPLIER
(R TOTAL)
CODE
First 4 digits
are significant
figures of
resistance
C
= 0.001
B
= 0.01
A
= 0.1
0
=1
1
= 10
2
= 100
3
= 1000
Ratio
TOL.
TCR
(ppm/°C)
TC Track
(ppm/°C)
G
=±2
J
=±5
K
= ± 10
N
= No
TERMINATION
G
= Au
A
= Al
BACK
METAL
VISUAL
CLASS
PACKAGING
CODE
E
= ± 25
B
= 0.1
C
= 0.25
C
= ± 50
D
= 0.5
K
= ± 100
F
= 1.0
M
= ± 250
G
= 2.0
J
= 5.0
N
= No
G
= Au
H
= Class H
WS
=
N
= None
K
= Class K Waffle pack
100 min,
1 mult
Historical Part Number: WCTR10150000K (will continue to
be
accepted)
Revision: 25-Feb-13
Document Number: 61020
2
For technical questions, contact:
efi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
京公网安备 11010802033920号
EEWORLD
