EEWORLDEEWORLDEEWORLD

Part Number

Search

DG3M824K

Description
Film Capacitor, Polyester, 1000V, 10% +Tol, 10% -Tol, 0.82uF,
CategoryPassive components    capacitor   
File Size891KB,20 Pages
ManufacturerAmerican Capacitor Corporation
Download Datasheet Parametric View All

DG3M824K Overview

Film Capacitor, Polyester, 1000V, 10% +Tol, 10% -Tol, 0.82uF,

DG3M824K Parametric

Parameter NameAttribute value
Objectid257099351
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
capacitance0.82 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPOLYESTER
high15.24 mm
length85.725 mm
negative tolerance10%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formAxial
positive tolerance10%
Rated (AC) voltage (URac)360 V
Rated (DC) voltage (URdc)1000 V
seriesD
width20.32 mm
A
MERICAN
C
APACITOR
C
ORPORATION
METALLIZED MYLAR CAPACITORS
ENVIRONMENTAL DATA
APPLICATIONS
Series D Metallized Mylar capacitors are superior
general purpose capacitors for both AC and DC
applications. They are dry-section, non-polar, non-
inductive wound capacitors with high volumetric effi-
ciency and a low cost.
Series D Capacitors come in several styles: Oval
Wrap & Fill (DW Style); Round Wrap & Fill (DR Style);
Axial Epoxy Case (DE Style); Radial Epoxy Case (DF
Style); Rectangular Hermetically Sealed (DG Style);
Round Hermetically Sealed (DL Style); Round Wrapped
Feed-Through (DQ Style). They are available in several
sizes including Regular (3 Size code) and Miniature (2
Size code) as well as custom sizes to meet specific
customer requirements.
Contact our Engineering Department for special sizes,
configurations, capacitance values and AC applications
with Anti-Corona construction at all frequencies.
Custom metal enclosures are available. Custom
designed Feed Through capacitors (DQ Style) are also
available for filter applications to specific requirements.
OPERATING TEMPERATURE RANGE
Range: -- 55°C to + 125°C, with voltage derating.
LIFE TEST
Series D capacitors shall be capable of withstanding a
test of 1000 hours at + 125°C and 100% of the derated
DC voltage or a test of 250 hours at + 125°C and 140%
of the derated DC voltage. The voltage shall be applied
to each capacitor through its individual current-limiting
resistor as determined from the formula R = 0.025/C,
where C is the nominal capacitance in farads and R is
in ohms.
The test procedures shall be in accordance with MIL-C-
18312, except as noted herein. Not more than one
failure in twelve shall be permitted. Any one of the
following shall be considered a failure.
a. A change in capacitance of more than 10% from
it’s initial value.
b. An increase in Dissipation Factor to a value
greater than 125% of the acceptance limit.
c. A decrease in Insulation Resistance to a value
less than 30% of the acceptance limit for + 25°C.
d. A permanent short or open.
ENGINEERING DATA SHEET
SERIES
D
New Flame Retardant Styles Available
VIBRATION
Series D capacitors shall be capable of withstanding a
vibration test in accordance with MIL-STD-202, Method
201. The following details and exceptions shall apply:
a.
Mounting.
The capacitor body shall be rigidly
mounted by the entire body length to the vibration test
fixture. The leads shall be soldered to rigidly supported
terminals and so spaced that the length of each lead
from the capacitor is 1/2
±
1/8 inch from the edge of
the supporting terminal.
b.
Measurement during Vibration.
During the last
cycle in each direction, an electrical measurement shall
be made to detect intermittent contacts (not to be
confused with "self healing" clearings) or open or short
circuiting.
c.
Examination After Vibration.
Capacitors shall
be visibly examined for evidence of mechanical dam-
age.
MOISTURE RESISTANCE
Series D capacitor Styles DG and DL (Hermetically
Sealed in metal containers) as well as Metal Can
Styles DB and DC shall be capable of withstanding the
moisture resistance, humidity, and temperature and
immersion cycling or MIL-C-18312. Styles DE and DF
(Epoxy Case), Styles DW and DR (Wrap & Fill) and
DQ (Feed-Through) capacitors are not intended for
exposure to high humidity conditions over extended
periods of time.
TERMINAL STRENGTH
Series D capacitors utilize tin-plated, copper-clad steel
wire terminals which shall be capable of withstanding
the following test without mechanical damage to the
capacitor or terminals:
a.
Pull Test.
The capacitor shall withstand a steady
pull of 5 pounds axially to the leads for 1 minute.
b.
Bend Test.
The wire lead terminals shall be bent
at a point of 1/4 inch from the body of the capacitor,
first 90 degrees in one direction, then back to the
original position, and then 90 degrees in the opposite
direction.
American Capacitor Corporation • 5367 Third Street, Irwindale, CA 91706 • Phone (626) 814-4444 • Fax (626) 814-4434
Web Site http://www.AmericanCapacitor.Com • E-mail Sales@AmericanCapacitor.Com
Copyright •
2009
Testing solutions for redundant link networks
[align=left]With the rapid development of communication technology, the role of the network in daily work is becoming more and more important, and Ethernet has gradually become the communication basis...
wenzhankwji Industrial Control Electronics
Key wireless technologies for 5G systems
...
btty038 RF/Wirelessly
[NXP Rapid IoT Review] + Rapid IoT App Running Error
[i=s]This post was last edited by bjemt on 2018-12-24 17:42[/i] I downloaded the Android phone App RAPID-IOT-1.1.5.apk from the NXP website and installed it on a Huawei M9 phone (Android 8). The App w...
bjemt RF/Wirelessly
How to Design an RF Power Amplifier: The Basics
How to Design an RF Power Amplifier: The Basics...
btty038 RF/Wirelessly
What is the principle of touch switch?
Dear experts, what is the principle of the single-open dual-control touch switch controlled by a single-chip microcomputer sold on Taobao? Single-open single-control is simple, but how is single-open ...
szzxl10 MCU
What is jitter and phase noise?
What is jitter and phase noise?Jitter reflects the time deviation of a digital signal from its ideal position. The bit period of high-frequency digital signals is very short, usually in the hundreds o...
btty038 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号