DL.5-124E-3 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> capacitor> DL.5-124E-3

DL.5-124E-3: DescriptionFilm Capacitor, Polyester, 50V, 10% +Tol, 10% -Tol, 0.12uF,; CategoryPassive components capacitor; File Size437KB，14 Pages; ManufacturerElectron Products Inc

Download Datasheet Parametric View All

DL.5-124E-3 Overview

Film Capacitor, Polyester, 50V, 10% +Tol, 10% -Tol, 0.12uF,

DL.5-124E-3 Parametric

Parameter Name	Attribute value
Objectid	831496523
package instruction	,
Reach Compliance Code	unknown
ECCN code	EAR99
capacitance	0.12 µF
Capacitor type	FILM CAPACITOR
diameter	5.969 mm
dielectric materials	POLYESTER
length	13.487 mm
negative tolerance	10%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package form	Axial
positive tolerance	10%
Rated (AC) voltage (URac)	40 V
Rated (DC) voltage (URdc)	50 V
Guideline	MIL-C-18312
series	D

Preview

Download Datasheet

View All

LECTRON

RODUCTS

METALLIZED MYLAR CAPACITORS

ENVIRONMENTAL DATA

APPLICATIONS

Series D Metallized Mylar capacitors are superior

general purpose capacitors for both AC and DC

applications. They are dry-section, non-polar, non-

inductive wound capacitors with high volumetric effi-

ciency and a low cost.

Series D Capacitors come in several styles: Oval

Wrap & Fill; Round Wrap & Fill (DC Style); Axial Epoxy

Case (DE Style); Radial Epoxy Case (D2E Style);

Rectangular Hermetically Sealed (DG Style); Round

Hermetically Sealed (DL Style); Round Wrapped Feed-

Through (DQ Style). They are available in several sizes

including Regular as well as custom sizes to meet

specific customer requirements.

Contact our Engineering Department for special sizes,

configurations, capacitance values and AC applications

with Anti-Corona construction at all frequencies.

Custom metal enclosures are available. Custom

designed Feed Through capacitors (DQ Style) are also

available for filter applications to specific requirements.

OPERATING TEMPERATURE RANGE

Range: -- 55°C to + 125°C, with voltage derating.

LIFE TEST

Series D capacitors shall be capable of withstanding a

test of 1000 hours at + 125°C and 100% of the derated

DC voltage or a test of 250 hours at + 125°C and 140%

of the derated DC voltage. The voltage shall be applied

to each capacitor through its individual current-limiting

resistor as determined from the formula R = 0.025/C,

where C is the nominal capacitance in farads and R is

in ohms.

The test procedures shall be in accordance with MIL-C-

18312, except as noted herein. Not more than one

failure in twelve shall be permitted. Any one of the

following shall be considered a failure.

a. A change in capacitance of more than 10% from

it’s initial value.

b. An increase in Dissipation Factor to a value

greater than 125% of the acceptance limit.

c. A decrease in Insulation Resistance to a value

less than 30% of the acceptance limit for + 25°C.

d. A permanent short or open.

ENGINEERING DATA SHEET

SERIES

New Flame Retardant Styles Available

VIBRATION

Series D capacitors shall be capable of withstanding a

vibration test in accordance with MIL-STD-202, Method

201. The following details and exceptions shall apply:

Mounting.

The capacitor body shall be rigidly

mounted by the entire body length to the vibration test

fixture. The leads shall be soldered to rigidly supported

terminals and so spaced that the length of each lead

from the capacitor is 1/2

1/8 inch from the edge of

the supporting terminal.

Measurement during Vibration.

During the last

cycle in each direction, an electrical measurement shall

be made to detect intermittent contacts (not to be

confused with "self healing" clearings) or open or short

circuiting.

Examination After Vibration.

Capacitors shall

be visibly examined for evidence of mechanical dam-

age.

MOISTURE RESISTANCE

Series D capacitor Styles DG and DL (Hermetically

Sealed in metal containers) as well as Metal Can

Styles shall be capable of withstanding the moisture

resistance, humidity, and temperature and immersion

cycling or MIL-C-18312. Styles DE and D2E (Epoxy

Case), Styles D and DC (Wrap & Fill) and DQ

(Feed-Through) capacitors are not intended for expo-

sure to high humidity conditions over extended periods

of time.

TERMINAL STRENGTH

Series D capacitors utilize tin-plated, copper-clad steel

wire terminals which shall be capable of withstanding

the following test without mechanical damage to the

capacitor or terminals:

Pull Test.

The capacitor shall withstand a steady

pull of 5 pounds axially to the leads for 1 minute.

Bend Test.

The wire lead terminals shall be bent

at a point of 1/4 inch from the body of the capacitor,

first 90 degrees in one direction, then back to the

original position, and then 90 degrees in the opposite

direction.

Electron Products Inc. • 5367 Third Street, Irwindale, CA 91706 • Phone (626) 960-2299 • Fax (626) 814-4434

Web Site http://www.ElectronProductsInc.Com • E-mail Sales@ElectronProductsInc.Com

Recommended Resources

Three-phase voltage transformer and commutation switch access circuit

Infrared remote control light switch

Pressure sensor module circuit

AC and DC 3-digit digital voltmeter circuit

Fishing alarm circuit diagram that can control multiple fishing rods

Winning amusement machine

TI document: How to program a DSP: This manual is a reference for programming the TMS320C6000 digital signalprocessor (DSP) device.Before using this book, you should install the code generation anddebugging tools.This book is divided i...; 灞波儿奔 DSP and ARM Processors

Live broadcast with prizes | Registration is open for TI chip technology to help motor development!: Prize-winning live broadcast | TI chip technology helps motor development registrationClick here to register for the live broadcastLive Topic TI chip technology helps motor developmentLive broadcast t...; EEWORLD社区 TI Technology Forum

80-bit extended precision floating point in OCaml: Is there an OCaml library that can take advantage of the 80-bit extended precision floating point types on the IA-32 and x86-64 architectures?Taking advantage of the historical floating point instruct...; fish001 DSP and ARM Processors

Tutorial: How to use Vivado HLS to accelerate algorithm development on FPGA: [align=left][color=rgb(34, 34, 34)][font=微软雅黑][size=4]This series of teaching videos is led by Xilinx senior strategic application engineers to guide you from scratch, step by step, to master Vivado H...; EE大学堂 Training Edition

[Contactless facial recognition access control system] + 1-MAIX_BIT development environment construction: [i=s]This post was last edited by manhuami2007 on 2022-7-7 19:48[/i]1. Introduction to MaixBit development board MaixBit is a development board designed by sipeed based on the K210 chip. The K210 chip...; manhuami2007 DigiKey Technology Zone

【Project source code】Data on FPGA-based DDR3: I'm sending you some ddr3 information to help you and others. Friends who are interested can take a look.attach://460080.rar...; 小梅哥 Altera SoC

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components