IS25LP256-RMLA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > IS25LP256-RMLA

Preview

IS25LP256-RMLA: Description3V SERIAL FLASH MEMORY WITH 166MHZ MULTI I/O SPI; File Size836KB，15 Pages; ManufacturerISSI(Integrated Silicon Solution Inc.); Websitehttp://www.issi.com/

Download Datasheet View All

IS25LP256-RMLA Overview

3V SERIAL FLASH MEMORY WITH 166MHZ MULTI I/O SPI

Preview

Download Datasheet

View All

ADVANCED INFORMATION

IS25LP256

256MBIT

3V SERIAL FLASH MEMORY WITH 166MHZ MULTI I/O SPI

& DTR INTERFACE

ADVANCED DATA SHEET

ADVANCED INFORMATION

IS25LP256

GENERAL DESCRIPTION

The IS25LP256 Serial Flash memory offers a versatile storage solution with high flexibility and performance in a

simplified pin count package. ISSI’s “Industry Standard Serial Interface” Flash is for systems that require limited

space, a low pin count, and low power consumption. The device is accessed through a 4-wire SPI Interface

consisting of a Serial Data Input (SI), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#) pins,

which can also be configured to serve as multi-I/O (see pin descriptions).

The device supports Dual and Quad I/O as well as standard, Dual Output, and Quad Output SPI. Clock

frequencies of up to 166MHz allow for equivalent clock rates of up to 664MHz (166MHz x 4) which equates to

over 80Mbytes/data throughput. The IS25xP series of Flash adds support for DTR (Double Transfer Rate)

commands that transfer addresses and read data on both edges of the clock. These transfer rates can

outperform 16-bit Parallel Flash memories allowing for efficient memory access to support XIP (execute in

place) operation.

The memory array is organized into programmable pages of 256 bytes. This family supports page program

mode where 1 to 256 bytes of data are programmed in a single command. QPI (Quad Peripheral Interface)

supports 2-cycle instruction further reducing instruction times. Pages can be erased in groups of 4Kbyte

sectors, 32Kbyte blocks, 64Kbyte blocks, and/or the entire chip. The uniform sector and block architecture

allows for a high degree of flexibility so that the device can be utilized for a broad variety of applications

requiring solid data retention.

GLOSSARY

Standard SPI

In this operation, a 4-wire SPI Interface is utilized, consisting of Serial Data Input (SI), Serial Data Output (SO),

Serial Clock (SCK), and Chip Enable (CE#) pins. Instructions are sent via the SI pin to encode instructions,

addresses, or input data to the device. The SO pin is used to read data or to check the status of the device.

This device supports SPI bus operation modes (0,0) and (1,1).

Mutil I/O SPI

Multi-I/O operation utilizes an enhanced SPI protocol to allow the device to function with Dual Output, Dual Input

and Output, Quad Output, and Quad Input and Output capability. Executing these instructions through SPI

mode will achieve double or quadruple the transfer bandwidth for READ and PROGRAM operations.

Quad I/O QPI

The device enables QPI protocol by issuing an “Enter QPI mode (35h)” command. The QPI mode uses four IO

pins for input and output to decrease SPI instruction overhead and increase output bandwidth. SI and SO pins

become bidirectional IO0 and IO1, and WP# and HOLD# pins become IO2 and IO3 respectively during QPI

mode. Issuing an “Exit QPI (F5h) command will cause the device to exit QPI mode. Power Reset or

Hardware/Software Reset can also return the device into the standard SPI mode.

DTR

In addition to SPI and QPI features, the device also supports SPI DTR READ. SPI DTR allows high data

throughput while running at lower clock frequencies. SPI DTR READ mode uses both rising and falling edges of

the clock to drive output, resulting in reducing the input and output cycles by half.

Programmable drive strength and Selectable burst setting.

The IS25LP256 offers programmable output drive strength and selectable burst (wrap) length features to

increase the efficiency and performance of READ operation. The driver strength and burst setting features are

controlled by setting the Read Registers. A total of six different drive strengths and four different burst sizes

(8/16/32/64 Byte) are available for selection.

Integrated Silicon Solution, Inc.- www.issi.com

Rev.00A

1/16/2014

Recommended Resources

FM-AM tuning circuit

Four-channel remote control switch transmitter circuit

Music guessing game circuit 03

Set base coupled monostable circuit

KPY series silicon piezoresistive absolute pressure sensor circuit

On-site signal optical fiber transmission and reception circuit

What interference? Will it break?: This is a simulation test of a DC24V to 3.3V power chip that is frequently short-circuited. The oscilloscope test waveforms are basically the same for the two wiring methods. The short-circuit mode is...; 呜呼哀哉 Analog electronics

What are the important parameters of commonly used rectifier diode models?: Rectifier diodes are generally planar silicon diodes used in various power rectifier circuits. When selecting rectifier diodes, the following important parameters should be considered. (1) Maximum ave...; 灞波儿奔 Analogue and Mixed Signal

Privileged students learn Verilog while coding Lesson01 Vivado download and installation: Privileged students learn Verilog while coding Lesson01 Vivado download and installation"If you want to do your work well, you must first sharpen your tools." The same is true for learning Verilog. Vi...; ove学习使我快乐 FPGA/CPLD

The principles and methods of 5G base station site selection have been learned: At present, my country has built the world's largest 5G independent networking network, with a total of 961,000 5G base stations in operation, of which more than 400,000 are jointly built and shared b...; 石榴姐 RF/Wirelessly

The difference between wireless module transmitting and receiving the same frequency and different frequencies: [color=rgb(51, 51, 51)][backcolor=rgb(225, 230, 215)][size=18px][backcolor=transparent][font=微软雅黑][backcolor=transparent][font=微软雅黑][font=微软雅黑][backcolor=transparent][font=微软雅黑][backcolor=transparent]...; dwzt Analog electronics

STM32 Network SMI Interface: 1Introduction to Ethernet The Ethernet peripheral of STM32F20X and STM32F21 can receive and send data according to the IEEE802.3-2002 standard.Ethernet provides a complete and flexible peripheral to m...; 嵌入式enjoy stm32/stm8

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components