TCXO
TG-5006CJ
Product name
TG-5006CJ-25L 19.200000 MHz
Product Number / Ordering code
X1G0041310016xx
Please refer to the 10.Packing information about xx (last 2 digits)
Output waveform
Clipped sine wave
Pb free / Complies with EU RoHS directive
Reference weight Typ.9.1mg
1.Absolute maximum ratings
Parameter
Symbol
Maximum supply voltage
Storage temperature
Min.
-0.3
-40
Typ.
-
-
Max.
4
90
Unit
V
ºC
Conditions / Remarks
Vcc terminal
Storage as single product
V
CC
-GND
T_stg
2.Operating Conditions
Parameter
Supply voltage
Operating temperature
Output load condition
Symbol
Vcc
T_use
Load_R
Load_C
Min.
1.7
-30
9
9
Typ.
-
-
25
10
10
Max.
3.3
-
85
11
11
Unit
V
ºC
kΩ
pF
Conditions / Remarks
GND = 0V
-
-
-
DC cut capacitor=0.01µF
DC-cut capacitor is not included in this TCXO. Please attach an external DC-cut capacitor (0.01 μF Min.) to the out pin.
(Vcc=1.8, 2.8, 3.0, 3.3 V, Vc=1.65 V, GND=0.0 V, Load 10 kΩ//10 pF(DC cut), T_use=+25ºC)
3.Frequency Characteristics
Parameter
Symbol
Output frequency
Frequency tolerance
Frequency /
temperature characteristics
Frequency / load coefficient
Frequency / voltage coefficient
Frequency slope
Min.
-
-2.0
-
-2
-
-0.2
-0.2
-
-
-
-1.0
-
-
Typ.
19.2000
-
-
-
-
-
-
-
-
-
-
-
-
Max.
-
2.0
-
2
-
0.2
0.2
-
-
-
1.0
-
-
Unit
MHz
x10
-6
x10
-6
x10
-6
x10
-6
x10
-6
/ ºC
x10
-6
Conditions / Remarks
T_use = +25ºC, Reflow 2 times
T_use = -30 ºC to +85 ºC
-
10 kΩ // 10 pF +/- 10%
Vcc +/- 5 %
-
-
-
1st year, T_use=25degC
-
-
f0
f_tol
f0-Tc
f0-Load
f0-Vcc
-
Frequency aging
f_age
*1 Include initial frequency tolerance and frequency deviation after reflow cycles.
*2 Measured in the elapse of 24 hours after reflow soldering.
*3 Vcc +/- 5% must be in operating supply voltage range (1.7 V to 3.47 V)
(Vcc=1.8, 2.8, 3.0, 3.3 V, Vc=1.65 V, GND=0.0 V, Load 10 kΩ//10 pF(DC cut), T_use=+25ºC)
4.Electrical Characteristics
Parameter
Current consumption
Symmetry
Output voltage
Harmonics
start up time
Phase noise
Symbol
Icc
SYM
Vp-p
-
tosc
L(f)
Min.
-
40
0.8
-
-
-
-
-
-
-
-
-
-
Typ.
-
-
-
-
-
-
-
-
-
-
-
-
-
Max.
1.5
60
1.5
-8
-
2.0
2.0
-87
-113
-135
-147
-148
-148
Unit
mA
%
V
dBc
ms
ms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Conditions / Remarks
T_Use = +25ºC , 10 kΩ//10pF
GND Level
Peak to peak 10 kΩ//10pF +/- 10%
-
-
Within 90% of final amp.
ΔF = +/- 1.0 x 10-6
Offset:10 Hz
Offset:100 Hz
Offset:1 kHz
Offset:10 kHz
Offset:100 kHz
Offset:1 MHz
1 Page
5.Timing chart
Output waveform (Clipped sine wave output)
V
p-p
GND
t
W
t
SYM=tw/t×100 %
6.Test circuit for TCXO
1) Output Load : 10 kΩ//10 pF
V
CC
N.C
Supply
Voltage
By-pass
Capacitor
0.01 mF
OUT
GND
0.01
Test Point
10 pF
10 kΩ
2) Current consumption
A
Supply
Voltage
By-pass
Capacitor
0.01 mF
V
CC
N.C
OUT
GND
0.01
10 pF
10 kΩ
3) Conditions
Impedance
Min. 1 MΩ
Input capacitance Max. 10 pF
Band width
Min. 300 MHz
Impossible to measure both frequency and wave form at the same time.(In case of using
oscilloscope's amplifier output, possible to measure both at the same time.)
2. Load_C includes probe capacitance.
3. A capacitor (By-pass:0.01 to 0.1 uF) is placed between V
CC
and GND,and closely to TCXO.
4. Use the current meter whose internal impedance value is small.
5. Power Supply
Impedance of power supply should be as low as possible.
1. Oscilloscope:
2 Page
7.External dimensions
2.0±0
#1
1.6±0.1
1.58
(Unit: mm)
#2
8.Footprint(Recommended)
0.6
(Unit: mm)
1.18
0.40
#4
0.73±0.07
0.27
1.2
#3
1.13
1.65
To maintain stable operation, provide a 0.01uF to 0.1uF
by-pass capacitor at a location as near as possible to the
power source terminal of the crystal product (between Vcc
- GND).
9.Reflow profile
Temperature[C]
300
250
200
150
100
50
Time
+25CtoPeak
0
60
120
180
240
300
360
420
480
540
600
660
720 780
Time[s]
;+217C
Tsmax;+200C
TL
TP
;+260C
+255C
Avg.
Ramp-up
3
C/sMax.
tp
;20sto40s
tL
60sto150s
(+217Cover)
Ramp-down
6C/sMax.
Tsmin;+150C
ts
60sto180s
(+150Cto+200C)
10.Packing information
[ 1 ]Product number last 2 digits code(xx) description
The recommended code is "00"
Code
14
15
16
Condition
1000pcs / Reel
2000pcs / Reel
3000pcs / Reel
X1G0041310016xx
Code
00
01
11
Condition
12000pcs / Reel
Any Q'ty vinyl bag(Tape cut)
Any Q'ty / Reel
3 Page
0.75
C0.15
[ 2 ] Taping specification
Subject to EIA-481 & IEC-60286
(1) Tape dimensions TE0804L
Material
of the Carrier Tape : PS
Material
of the Top Tape : PET+PE
φ
1 .5
+0 .1
0
Unit: mm
1 .75±0 .1
1 .0±0 .1
0 .25±0 .05
4 .0 ±0 .1
2 .0±0 .1
3 .5±0 .1
8 .0±0 .2
φ
13.00. 2
4 .0±0 .1
φ
1 .0
1 .85±0 .1
+0 .1
0
(2) Reel dimensions
Center material
: PS
Material of the Reel : PS
13.4
1. 0
9.4
1.0
2 .25±0 .1
2.0
0 . 5
4 Page
φ
330.0
2 . 0
φ
100.0
11.Handling precautions
Prior to using this product, please carefully read the section entitled “Precautions” on our Web site
(
http://www5.epsondevice.com/en/quartz/tech/precaution/
) for instructions on how to handle and use the
product properly to ensure optimal performance of the product in your equipment. Before using the product under
any conditions other than those specified therein, please consult with us to verify and confirm that the
performance of the product will not be negatively affected by use under such conditions.
In addition to the foregoing precautions, in order to avoid the deteriorating performance of the product, we
strongly recommend that you DO NOT use the product under ANY of the following conditions:
(1) Mounting the product on a board using water-soluble solder flux and using the product without removing
the residue of the flux completely from the board. The residue of such flux that is soluble in water or
water-soluble cleaning agent, especially the residues which contains active halogens, will negatively
affect the performance and reliability of the product.
(2) Using the product in any manner that will result in any shock or impact to the product.
(3) Using the product in places where the product is exposed to water, chemicals, organic solvent, sunlight,
dust, corrosive gasses, or other materials.
(4) Using the product in places where the product is exposed to static electricity or electromagnetic waves.
(5) Applying ultrasonic cleaning without advance verification and confirmation that the product will not be
affected by such a cleaning process, because it may damage the crystal, IC and/or metal line of the
product.
(6) Touching the IC surface with tweezers or other hard materials directly.
(7) Using the product under any other conditions that may negatively affect the performance and/or
reliability of the product.
(8) Using the product with power line ripple exceeding 50 mV(p-p) level.
Should any customer use the product in any manner contrary to the precautions and/or advice herein, such use
5 Page
京公网安备 11010802033920号
EEWORLD
