MEMS Oscillator, Low Power, LVCMOS, 115.000 MHz to 137.000 MHz
Features:
MEMS Technology
Direct pin to pin drop-in replacement for industry-standard packages
LVCMOS Compatible Output
Industry-standard package 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5, 5.0 x 3.2, and 7.0 x 5.0 mm x mm
Six supply voltages options, +1.8 V, +2.5 V, +2.8 V, +3.3 V and +2.25 V to +3.63 V continuous
Pb-free, Halogen-free, Antimony-free
RoHS and REACH compliant
Fast delivery times
IM802 Series
Typical Applications:
Fibre Channel
Server and Storage
GPON, EPON
100M / 1G /10G Ethernet
Electrical Specifications:
Frequency Range
Frequency Stability
Operating Temperature
Supply Voltage (Vdd) ±10%
Current Consumption
OE Disable Current
Standby Current
Waveform Output
Symmetry (50% of waveform)
Rise / Fall Time
Logic “1”
Logic “0”
Input Characteristics
Input High Voltage
Input Pull-up Impedance
Startup Time
Enable Disable Time
Resume Time
RMS Period Jitter
Peak-to-peak Period Jitter
RMS Phase Jitter (random)
115.000 MHz to 137.000MHz
See Part Number Guide
See Part Number Guide
See Part Number Guide
6.2 mA typ./ 7.5 mA max
5.5 mA typ./ 6.4 mA max
4.9 mA typ./ 5.6 mA max
4.2 mA max
4.0 mA max
2.6 µA typ./ 4.3 µA max
1.4 µA typ./ 2.5 µA max
0.6 µA typ./1.3 µA max
LVCMOS / HCMOS
45%/55%
1.0 nSec typ./ 2.0 nSec max
1.3 nSec typ./ 2.5 nSec max
90% of Vdd min
10% of Vdd max
70% of Vdd max
30% of Vdd min
50kΩ min / 87kΩ typ. 150kΩ max
2.0MΩ min
5 mSec max
122 nSec max
5 mSec max
1.9 pSec typ,/ 3.0 pSec max
1.8 pSec typ./ 4.0 pSec max
12.0 pSec typ./ 25.0 pSec max
14.0 pSec typ./ 30.0 pSec max
0.5 pSec typ./ 0.9 pSec max
1.3 pSec typ./ 2.0 pSec max
Inclusive of Initial Tolerance, Operating Temperature Range, Load,
Voltage, and Aging (First year at +25ºC)
No load condition, F = 125 MHz, Vdd = +2.8V, +3.0V, = +3.3 V
No load condition, F = 125 MHz, Vdd = +2.5 V
No load condition, F = 125 MHz, Vdd = +1.8 V
Vdd = +2.5 V to +3.3 V, OE = GND, Output in high-Z state
Vdd = +1.8 V, OE = GND, Output in high-Z state
ST
= GND, Vdd = +2.8 V to +3.3V
ST
= GND, Vdd = +2.5 V
ST
= GND, Vdd = +1.8 V
All supply voltages
Vdd = +2.5 V, +2.8 V, + 3.0 V or +3.3 V from 20% to 80% of waveform
Vdd = +1.8 V from 20% to 80% of waveform
Pin 1, OE or
ST
Pin 1, OE or
ST
Pin 1, OE logic high or logic or
ST
logic high
Pin 1,
ST
logic Low
Measured from the time Vdd reaches its rated minimum value
F=137 MHz For other frequencies Toe = 100 nSec + 3 cycles
Measured from the time
ST
pin crosses 50% threshold
F= 125 MHz, Vdd = +2.5 V, +2.8 V, + 3.0 V or +3.3 V
F = 125 MHz, Vdd = +1.8 V
F = 125 MHz, Vdd = +2.5 V, +2.8 V, + 3.0 V or +3.3 V
F = 125 MHz, Vdd = +1.8 V
Integration Bandwidth = 900 kHz to 7.5 MHz
Integration Bandwidth = 12 kHz to 20.0 MHz
Notes:
1. All min and max limits are specified over temperature and rated operating voltage with 15pF output unless otherwise stated.
2. Typical values are at +25ºC and nominal supply voltage.
3333
Absolute Maximum
Limits
Storage Temperature
Supply Voltage (Vdd)
Electrostatic Discharge
Solder Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
-65ºC to +150ºC
-0.5 VDC to 4.0 VDC
2000 V max
260ºC max
150ºC max
ILSI America Phone 775-851-8880
●
Fax 775-851-8882
●email:
e-mail@ilsiamerica.com
●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 08/18/17_B
Page 1 of 9
MEMS Oscillator, Low Power, LVCMOS, 115.000 MHz to 137.000 MHz
Ordering Information
Part Number Guide
Packages
IM802A – 7.0 x 5.0
IM802B – 5.0 x 3.2
IM802C – 3.2 x 2.5
IM802D – 2.5 x 2.0
IM802E – 2.0 x 1.6
Input Voltage
1 = +1.8 V
6 = +2.5 V
2 = +2.7 V
7 = +3.0 V
3 = +3.3 V
8 = +2.25 V to +3.63 V
Operating
Temperature
1 = 0ºC to +70ºC
2 = -40ºC to +85ºC
3 = -20ºC to +70ºC
Output Drive
Strength
- = Default
(see tables 2
through 6)
Stability
(ppm)
E = ±10
F = ±20
A = ±25
B = ±50
Select
Function
H = Tri-state
S = Standby
O = N/C
IM802 Series
Frequency
- Frequency
Sample Part Number:
IM802C-62-FS-100.0000MHz
This 100.0000 MHz oscillator in a 3.2 x 2.5 package with stability ±20 ppm from -40ºC to +85ºC using a supply voltage of +2.5 V. The Output Drive Strength
(Rise and Fall Time) is 0.96 nSec per Table 3 with 15 pF load. With Pin 1 function as Standby
Sample Part Number:
IM802B-71EAO-133.0000MHz
This 133.0000 MHz oscillator in a 5.0 x 3.2 package with stability ±25 ppm from 0ºC to +70ºC using a supply voltage of +3.0 V. The Output Drive Strength
(Rise and Fall Time) is 1.00 nSec per Table 3 with 15 pF load. With Pin 1 function is not connected
Notes:
Not all options are available at all frequencies and temperatures ranges.
Please consult with sales department for any other parameters or options.
Oscillator specification subject to change without notice.
Test Circuit
Waveform
ILSI America Phone 775-851-8880
●
Fax 775-851-8882
●email:
e-mail@ilsiamerica.com
●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 08/18/17_B
Page 2 of 9
MEMS Oscillator, Low Power, LVCMOS, 115.000 MHz to 137.000 MHz
Performance Plots:
IM802 Series
Figure 1: Idd vs Frequency
Figure 2: Frequency vs Temperature, 1.8 V
Figure 3: RMS Period Jitter vs Frequency
Figure 4: Duty Cycle vs Frequency
Figure 5: 20% to 80% Rise Time vs Temperature
Figure 6: 20% to 80% Fall Time vs Temperature
ILSI America Phone 775-851-8880
●
Fax 775-851-8882
●email:
e-mail@ilsiamerica.com
●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 08/18/17_B
Page 3 of 9
MEMS Oscillator, Low Power, LVCMOS, 115.000 MHz to 137.000 MHz
Performance Plots (Cont.)
IM802 Series
Figure 7: RMS Integrated Phase Jitter Random
(12 kHz to 20 MHz vs Frequency)
Figure 8: RMS Integrated Phase Jitter Random
(900 kHz to 20 MHz vs Frequency
Notes:
All plots are measured with 15pF load at room temperature unless otherwise stated.
Phase noise plots are measured with Agilent E5052B signal source analyzer integration range is up to 5 MHz for carrier frequencies below 40 MHz
Environmental Specifications:
Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL Level 1 at +260ºC
Pb Free Solder Reflow Profile
Ts max to T
L
(Ramp-up Rate)
Preheat
Temperature min (Ts min)
Temperature typ (Ts typ)
Temperature max (Ts max)
Time (Ts)
Ramp-up Tate (T
L
to Tp
Time Maintained Above
Temperature (T
L
)
Time (T
L)
Peak Temperature (Tp)
Time within 5ºC to Peak
Temperature (Tp)
Ramp-down Rate
Tune 25ºC to Peak Temperature
Moisture Sensitivity Level (MSL)
3ºC / second max
150ºC
175ºC
200ºC
60 to180 seconds
3ºC / second max
217ºC
60 to 150 seconds
260ºC max for seconds
20 to 40 seconds
6ºC / second max
8 minute max
Level 1
Units are backward compatible with +240ºC reflow processes
ILSI America Phone 775-851-8880
●
Fax 775-851-8882
●email:
e-mail@ilsiamerica.com
●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 08/18/17_B
Page 4 of 9
MEMS Oscillator, Low Power, LVCMOS, 115.000 MHz to 137.000 MHz
Pin Functionally
Pin
Symbol
OE
ST
Tri-state
Standby
Pin Description
Functionality
High or Open = specified frequency output
Low = Output is high impedance, only output is disabled.
High or Open = specified frequency output.
Low = Output is low. Device goes to sleep mode. Supply current
reduces to standby current.
Any voltage between 0.0 V to Vdd or Open = specified frequency
output
Pin 1 has no functiion
Electrical ground
Oscillator output
Power supply voltage
IM802 Series
Pin Assignments
1
N/C
No Connect
OE
ST 1
N/C
Top View
4
Vdd
2
GND
Power
3
Out
Output
4
Vdd
Power
Notes:
1. In OE or
ST
mode, a pull-up resistor of 10.0 kΩ or less is recommended if Pin 1 is not externally
driven. If Pin 1 needs to be left floating, use the NC option.
2. A capacitor of value 0.1 µF or higher between Pin 4 (Vdd) and Pin 1 (GND) is required.
GND 2
3
OUT
Pin 1 Configuration Options (OE, or
Output Enable (OE) Mode
, or NC)
Pin 1 of the IM802 can be factory-programmed to support three modes: Output Enable (OE), Standby (
ST
) or No Connect (NC).
In the OE mode, applying logic Low to the OE pin only disables the output driver and puts it in Hi-Z mode. The core of the device
continues to operate normally. Power consumption is reduced due to the inactivity of the output. When the OE pin is pulled High, the
output is typically enabled in <1 µSec.
Standby
Mode
In the ST mode, a device enters into the standby mode when Pin 1 pulled Low. All internal circuits of the device are turned off. The
current is reduced to a standby current, typically in the range of a few µA. When
ST
is pulled High, the device goes through the
“resume” process, which can take up to 5 mSec.
No Connect (NC) Mode
In the NC mode, the device always operates in its normal mode and outputs the specified frequency regardless of the logic level
on Pin 1.
Table 1 below summarizes the key relevant parameters in the operation of the device in OE, ST, or NC mode.
In "Investigating Things to Gain Knowledge 06 - The Water-Dropping Generator", we introduced the water-dripping generator invented by British scientist Kelvin in 1867. Figure (01) is a schematic diagr...
Let me introduce to you the UWB promotion organization - Fira Alliance. In order to promote UWB globally, in August 2019, NXP, Samsung, Bosch, Sony and other companies formed the FiRa Alliance (fine r...
lvgl has been successfully ported before, and can be used to draw some HMI interfaces. Today, an LVGL QR code library is implemented to display some data through QR code. The QR code library can also ...
Overview
The RS485 interface forms a half-duplex network, adopts a combination of balanced drivers and differential receivers, uses shielded twisted pair transmission, and has strong resistance to com...
As shown in the picture, is the Q3Q4 circuit drawn incorrectly? A push-pull circuit should not be drawn like this. Today I saw an old professor drawing it like this, and I was afraid to ask, isn't Q3Q...
1. Hardware Introduction
RVB2601 has built-in the high-performance and secure WiFi4 chip W800 from Lianshengde. W800 is connected to CH2601 via the SPI port (blue frame line) as shown below:2. Softwar...
As early as 2018, SigmaStar and Aihua Yingtong signed a strategic cooperation agreement and reached a strategic cooperation relationship. The two parties will join forces to jointly carry out various...[Details]
3D Glass Solutions (3DGS) has raised $20 million in Series B1 funding led by Intel Capital. CerraCap Ventures, Lockheed Martin Ventures and Nagase & Co also participated. As a result of this round of...[Details]
In the latest emergency update, Google fixed two vulnerabilities in the Chrome browser, one of which has been proven to be exploited by hackers. The emergency update released this week applies not on...[Details]
ARM assembly language programming: The statements in the ARM assembly language source program are composed of instructions, pseudo operations and macro instructions. ARM instructions have been introd...[Details]
As an important part of smart grid, the development of smart meter plays an irreplaceable role in
the growth of
smart grid
. This article includes the structural classification, working princip...[Details]
At present, medical staff generally cannot accompany patients throughout the whole process, which will bring many safety risks and inconveniences to patients and medical staff. This paper designs a...[Details]
Imagination’s automotive experience and virtualisation offerings set it apart from its competitors London, UK and Seoul, South Korea – 19 June 2019 – Imagination Technologies ’ PowerVR Series9XT...[Details]
Multi-stage amplifier circuit
1. Multi-stage amplifier circuit and its coupling method
In many applications, the amplifier is required to have a higher gain and appropriate input and output re...[Details]
According to Strategy Analytics, the global smartphone application processor (AP) market achieved double-digit year-on-year revenue growth for the sixth consecutive quarter in the second quarter of 2...[Details]
Inscription: When I first started practicing 51, I used C language. Now I want to strengthen assembly, so I have to learn the hardware structure of the microcontroller, especially the allocation of ad...[Details]
/* This program can read the root directory of a FAT16 file system USB flash drive with 180 lines of C code. You can see the file name under the root directory and display the content of the first fi...[Details]
The Importance of
Power
Monitoring in High-Speed
Circuit
Boards
The power supply is the simplest device in the system being designed, but it must be considered last in the desig...[Details]
Wearable devices will become a new application driving the growth of demand for micro-electromechanical systems (MEMS). As the personal computer (PC) market shrinks and the growth rate of smartphone ...[Details]
Maxim Integrated and SICK AG have collaborated to introduce the industry’s smallest LiDAR safety scanner.
For many designers, the biggest drawbacks to using LiDAR technology in their app...[Details]
introduction
DC regulated power supply is a commonly used electronic device, which can ensure stable output voltage when the grid voltage fluctuates or the load changes. A low ripple, h...[Details]
Circuit Observation Room
京公网安备 11010802033920号
EEWORLD
