Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
Prepare the evaluation kit and connect it to the LaunchPad development kit
The LMG5200 evaluation module (EVM) comes with a circuit that drives the GaN integrated circuit (IC). You need to disconnect ...
[i=s]This post was last edited by xulikai on 2019-10-20 10:36[/i]This content is originally created by EEWORLD forum user xulikai . If you want to reprint or use it for commercial purposes, you must o...
[size=4]1) Single-step operation is possible, but continuous operation always returns to address 0: Watchdog is not turned off, and continuous operation resets DSP back to address 0. [/size] [size=4]2...
[i=s] This post was last edited by xld0932 on 2019-4-15 19:36 [/i] 1. The installation steps of KEIL software are omitted. Open KEIL software, click Help->About uVision... in the menu bar, and a dialo...
The so-called Wi-Fi 6, also known as 802.11ax, is an upgraded version of the previous generation technology 802.11ac (also known as Wi-Fi 5). Compared with the previous generation of technology, Wi-Fi...
Voltage Regulator
The power voltage stabilizer is divided into single-phase and three-phase types. It is designed and manufactured using internationally advanced compensation technology and has the...[Details]
There are always some great people who are not satisfied with the appearance of current products and want to create different products. That’s why there is this mobile phone that can be used f...[Details]
;Use the serial port debugging wizard or the PC terminal's hyperterminal, set the baud rate to 9600, 8 data bits, 1 stop bit, no parity bit. ;First, send a character such as "2" from the PC to the se...[Details]
Recently, the fully direct supply green intelligent heavy truck swap station project built by the State Energy Group in Xiaolongtan Town, Kaiyuan City was completed and put into use. This is the first...[Details]
Ford Motor has three brands: Ford, Lincoln, and Mercury. Its important models include Thunderbird, Mustang, F-series trucks, and T-series cars. The article does not involve Changan Ford, Jiangling ...[Details]
Micron's 1β advanced process-based DRAM delivers up to 8,000 MT/s, providing better solutions for memory-intensive applications such as generative AI
November 22, 2023, Shanghai, Chi...[Details]
3. Serial port interrupt service thread After the serial port interrupt is generated, the specific data processing will be completed in the interrupt service thread. Take the camera interrupt thread ...[Details]
1. Light up the conjecture at the same time In the first section of this chapter, we said that if we want to light up the digital tube, then the small LED light we learned in the first chapter will...[Details]
summary:
With the rapid development of intelligent connected vehicle technology, its information security issues have gradually become the focus of public attention. This pape...[Details]
HSH8927 is a new dual-channel audio circuit from PHILIPS. It has an input mute function, no current impact sound when turning on/off, and overload short circuit protection, which is suitable for the ...[Details]
The new Japanese chip factory being built by TSMC is the product of a long-standing relationship between the world's largest foundry and a country seeking to regain influence in the global semiconduc...[Details]
When the product is designed for low power consumption, we will use some methods to do some low power consumption processing. However, after achieving low power consumption, we are worried that the p...[Details]
When I first started using RF communication, I quickly completed data transmission with the help of Chengdu Yibite's demo, but the power consumption could not be reduced. The official datasheets of S...[Details]
In an era of rapid technological advancement,
emerging technologies such as
robotics
and artificial intelligence are constantly driving the upgrading of traditional industries.
On March...[Details]
I started to get involved in embedded systems by learning microcontrollers, so I always felt that I should start from the hardware and then move on to the drivers. This learning process made it eas...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
