Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
Abdominal breathing training trainerAuthor:7905Project Background ( 100-200words ) Whether it is ancient Indian yoga or Buddhist meditation, or Chinese Taoist Dandao fetal breathing and ordinary Qigon...
ST MEMS Device Resource Library: Click to enterSub-library: Hardware Design Guidance
The unique process and principle of MEMS lead to higher requirements in hardware design . Improper hardware design ...
FF0000 and 880000 are both red. What is the difference between these two reds?Another question is, are reds of different saturations pure red, or are they mixed with other colors?...
1. Brief Introduction
After completing the data request, you also need to write the software interface. The system comes with the LVGL graphical interface, but to be honest, using LVGL for monochrome ...
Automotive-grade MCU is the core of automotive electronic system control and the key to the transformation of the automotive industry to electrification and intelligence. In recent years, with the im...[Details]
XTAL1 and XTAL2 are the input and output of the inverting amplifier of the on-chip oscillator, as shown in Figure 13. This oscillator can be used with a quartz crystal or a ceramic resonator. The os...[Details]
1. Basic concepts of serial ports In the STM32 reference manual, the serial port is described as a universal synchronous asynchronous receiver and transmitter (USART), which provides a flexible metho...[Details]
Excitation of the vibrating wire sensor by the acquisition instrument: also called "excitation", is a necessary process for obtaining frequency data of the vibrating wire sensor. Only when the sensor...[Details]
The baud rate of the debugging serial port is modified, and the serial port cannot print quickly, resulting in the inability to download the program Freertos plus i2c plus multiple 4 serial port prog...[Details]
1. Influence of insertion depth (1) Selection of temperature measurement points The installation position of the thermocouple, that is, the selection of the temperature measurement point, is th...[Details]
On February 2, the China Securities Regulatory Commission issued an announcement stating that recently, the Commission has approved the registration of the initial public offering of shares of Xingj...[Details]
1 Introduction
With the rapid development of microelectronics technology, various electronic products have emerged continuously and are developing towards the trend of being portable, small an...[Details]
On August 6, State Grid Corporation of China held a mobilization meeting for the construction of the Qinghai Walang Pumped Storage Power Station and the Yushu Golog Second Circuit and Dingzikou Tra...[Details]
Batteries will be key to Japan's goal of becoming carbon neutral by 2050. They are the most important technology for the electrification of cars and other mobile devices and are essential for adjusti...[Details]
The software implementation mainly involves hardware initialization and simple wireless transmission and reception based on the IEEE820.15.4 format.
Hardware initialization includes clock initializat...[Details]
Ford Front End Accessory Drive Division Cuts Test Cycle Time in Half with LMS Test.Lab Ford Motor Company has been committed to building high-quality, fuel-efficient, safe and technologically advance...[Details]
Qt/Embedded is a Linux-based embedded platform development tool launched by Qiqu Technology. It is an embedded version of Qt. Since KDE and other projects use Qt as a support library, many X Window...[Details]
At the just-concluded 2023 CES, BMW released the i Vision Dee concept car equipped with a large-size HUD, and also integrated display systems on the front windshield and other glass. BMW Group CEO Ol...[Details]
In order to meet the ignition work of explosive bridge wires with different resistance values in a narrow space, a certain engineering test ignition device requires a switching power supply wit...[Details]
ST MEMS Sensor Creative Design Competition
京公网安备 11010802033920号
EEWORLD
