PWA
www.vishay.com
Vishay Electro-Films
Thin Film Power Resistors
FEATURES
•
•
•
•
•
•
Product may not be to scale
The PWA series resistor chips offer a 500 mW power rating
in a small size. These offer one of the best combinations of
size and power available.
The PWAs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The PWAs are 100 % electrically tested and
visually inspected to MIL-STD-883, method 2032, class H or
class K.
Wire bondable
500 mW power
Chip size: 0.030" x 0.045"
Case: 0503
Resistance range 0.3
to 1 M
Oxidized silicon substrate for good power
dissipation
• Resistor material: Tantalum nitride, self-passivating
• Material categorization: for definitions of compliance
please see
www.vishay.com/doc?99912
APPLICATIONS
The PWA resistor chips are used mainly in higher power
circuits of amplifiers where increased power loads require a
more specialized resistor.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
VALUE
0.3 to 1M
± 0.1, ± 0.5, ± 1, ± 5
± 25, ± 50, ± 100, ± 150
Tightest Standard Tolerance Available
5%
1%
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 150 ppm/°C
UNIT
%
ppm/°C
5
Ω
100
Ω
0.3
Ω
2
Ω
25
Ω
*600, - 100 ppm R < 2
Ω,
± 250 ppm for 2
Ω
to 5
Ω
200 kΩ 500 kΩ
300 k
Ω
1 M
Ω
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
to 250 k
< 100
or > 251 k
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, +125 °C, 250 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, +150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
Steady State
5 x Rated Power
DC Power Rating at + 70 °C (Derated to zero at + 175 °C)
(Conductive epoxy die attach to alumina substrate)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Revision: 29-Apr-15
VALUE
-35 typ.
-20 typ.
± 0.5 max.
R/R
± 0.5 max.
R/R
-55 to +125
± 0.1 max.
R/R
± 0.2 max.
R/R
200
10
12
min.
UNIT
dB
%
%
°C
%
%
V
V
W
%
100 max.
200 max.
0.5
± 0.1 max.
R/R
Document Number: 61019
1
For technical questions, contact:
efi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
PWA
www.vishay.com
DIMENSIONS
in inches
0.030
0.024
0.007
0.007
0.030
0.024
0.007
0.030
0.024
0.030
0.024
0.007
Vishay Electro-Films
0.0045
0.045
0.045 0.045
0.007
TYPICAL RANGE
0.3
Ω
to 1.3
Ω
TYPICAL RANGE
1.4
Ω
to 7.4
Ω
TYPICAL RANGE
7.5
Ω
to 42
Ω
TYPICAL RANGE
43
Ω
to 1 MΩ
SCHEMATIC
MECHANICAL SPECIFICATIONS
PARAMETER
Chip Size
Chip Thickness
Chip Substrate Material
Resistor Material
Bonding Pad Size
Number of Pads
Pad Material
Backing
VALUE
0.030" x 0.045" ± 0.002" (0.762 mm x 1.143 mm ± 0.5 mm)
0.010" ± 0.002" (0.254 mm ± 0.05 mm)
Oxidized silicon, 10 kÅ minimum SiO
2
Tantalum nitride, self-passivating
0.007" x 0.024" (0.1778 mm x 0.6096 mm)
2
10 kÅ minimum aluminum (Au optional)
None, lapped semiconductor silicon (Au back optional)
GLOBAL PART NUMBER INFORMATION
Global Part Number: PWA50000FKANHWS
Global Part Number Description: PWA 5K 1 % 100 ppm Al None H WS
P
W
A
5
0
0
0
0
TCR
(ppm/°C)
E
= ± 25
C
= ± 50
K
= ± 100
V
= ± 150
L
= ± 200
M
= ± 250
Z
= + 600/
- 100
F
K
A
N
BACK
METAL
H
VISUAL
CLASS
W
S
PACKAGING
CODE
MODEL
PWA
30 x 45
size
Power
resistor
RESISTANCE
First 4 digits are
significant figures
of resistance
RESISTANCE
MULTIPLIER
CODE
D
= 0.0001
C
= 0.001
B
= 0.01
A
= 0.1
0
=1
1
= 10
2
= 100
3
= 1000
TOLERANCE
CODE
(%)
B
= 0.1
C
= 0.25
D
= 0.5
F
= 1.0
G
= 2.0
H
= 2.5
J
= 5.0
K
= 10
TERMINATION
G
= Au
A
= Al
G
= Au
H
= Class H
WS
= Waffle pack
N
= None
K
= Class K 100 min, 1 mult
Revision: 29-Apr-15
Document Number: 61019
2
For technical questions, contact:
efi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
ADI Reference Circuit
京公网安备 11010802033920号
EEWORLD
