EEWORLDEEWORLDEEWORLD

Part Number

Search

HBSTCR-125-S-XXX-34-GT-200-LT

Description
Board Connector, 25 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Receptacle
CategoryThe connector    The connector   
File Size170KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

HBSTCR-125-S-XXX-34-GT-200-LT Overview

Board Connector, 25 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Receptacle

HBSTCR-125-S-XXX-34-GT-200-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid1163319000
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresLEAD LENGTH=1.430 INCH
body length2.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial numberHBSTCR
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature250 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts25
[Evaluation of the popular N32G45XVL model of the National Technology M4 core] Part 6 Preparation for motor application development
[i=s]This post was last edited by oxygen_sh on 2022-3-17 19:54[/i]I am going to use the National Technology M4 development board to make a three-phase motor control application. I searched the box and...
oxygen_sh Domestic Chip Exchange
AR1021X uses hostapd to configure AP hotspots.
When applying AR1021X modular integration, some applications need to use modules as soft AP, which involves the hostapd configuration problem. If the configuration is not good, there will be no SSID h...
natertech Embedded System
Design method of adding soft start to DCDC chip
Problem description:For most chips, there is usually a soft start pin in the chip's function pins. Its function is to slowly increase the output voltage to the set value and reduce the inrush at the s...
qwqwqw2088 Analogue and Mixed Signal
The stm32 board runs normally online, but does not function normally when it is powered on again
1. I recently encountered this problem when adjusting the board: the board functions normally when the emulator is plugged in and running online, but some functions of the board are abnormal when it i...
shijizai stm32/stm8
Four points of detailed description of field effect tube application
We often come into contact with crystal triodes and are familiar with their use. Relatively speaking, we are a little unfamiliar with crystal field effect tubes. However, due to the unique advantages ...
唯小样 Power technology
High-frequency equivalent circuits and characteristic curves of resistors, capacitors and inductors
1. High frequency resistor The most common circuit element in low-frequency electronics is the resistor, which is used to reduce voltage by converting some electrical energy into heat. The high-freque...
火辣西米秀 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号