SINGLE-POLE SINGLE-THROW SWITCHES
FEATURES
•
•
•
•
•
•
Multioctave bands 0.2 to 18 GHz
Current or TTL control
Low insertion loss
High isolation
Ultra high speed models (5 ns) available
Drop-in models available
Frequency
Range
(GHz)
Model
Number
SW1-002020RN1NF
SW1-002020AN1NF
SW1-005020RN1NF
SW1-005020AN1NF
SW1-020080RN1NF
SW1-020080AN1NF
SW1-040120RN1NF
SW1-040120AN1NF
SW1-020180RN1NF
SW1-020180AN1NF
SW1-010180RN1NF
SW1-010180AN1NF
Insertion
Loss
(dB, Max.)
1.7
1.8
1.5
1.7
2
2.2
2.2
2.6
3
3
3
3.2
Isolation
(dB, Min.)
70
75
80
75
80
70
80
65
80
60
70
60
VSWR*
(Max.)
1.6:1
1.6:1
1.6:1
1.6:1
1.7:1
1.7:1
1.7:1
1.7:1
2:1
2:1
2:1
2:1
Type
Reflective
Absorptive
Reflective
Absorptive
Reflective
Absorptive
Reflective
Absorptive
Reflective
Absorptive
Reflective
Absorptive
Rise/Fall
Time
(ns, Typ.)
10/10
10/10
10/10
10/10
10/10
10/10
10/10
10/10
10/10
10/10
10/10
10/10
On/Off
Time
(ns, Typ.)
20
20
20
20
20
20
20
20
20
20
20
20
On/Off
DC Power
Time
Positive Negative
(ns, Max.) (mA, Max.) (mA, Min.)
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
70
70
70
70
70
70
70
70
70
70
70
70
STANDARD, MULTIOCTAVE BAND MODELS
0.2–2
0.5–2
2–8
4–12
2–18
1–18
OPTIMIZED PERFORMANCE MODELS
0.8–18
0.1–20
0.5–2
0.5–18
2–2.2
2–8
3–3.4
3–9
3.5–4.5
9–9.2
9.1–9.7
SW1-008180RN1NF
SW1-001200RN1NF
SW1-005020AN1NF
SW1-005180RN1NF
SW1-020022RN1NF
SW1-020080AN1NF
SW1-030034AN1NF
SW1-030090RN1NF
SW1-035045AN1NF
SW1-090092RN1NF
SW1-091097AI2NF
4
5
1.8
3
1
2
1
1.7
2
1
2.6
70
80
75
70
40
55
60
60
80
70
65
2:1
2:1
1.6:1
2:1
1.7:1
1.7:1
1.5:1
1.7:1
1.7:1
1.7:1
1.7:1
Reflective
Reflective
Absorptive
Reflective
Reflective
Absorptive
Absorptive
Reflective
Absorptive
Reflective
Absorptive
5
10
8
10
20
5
10
10
20
20
10
35
35
35
35
35
35
35
35
35
35
30
40
40
40
40
40
40
40
40
40
40
35
35
35
35
35
70
35
35
35
60
35
35
35
35
35
70
70
35
70
70
60
70
70
Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lower
insertion loss, lower VSWR, higher isolation, high power and flat amplitude response. Mechanical/Control options include: Custom packaging, single
supply operation, and ultra-fast on/off time. Consult MITEQ for options.
*For reflective models, VSWR is not specified in the “Off” state. For absorptive models, VSWR in the “Off” state is defined for port J2 only.
100 Davids Drive, Hauppauge, NY 11788 • TEL: (631) 436-7400 • FAX: (631) 436-7430 •
www.miteq.com
SINGLE-POLE SINGLE-THROW SWITCHES (CONT.)
TTL CONTROL LOGIC
Non-inverting Logic 0
Logic 1
Inverting
Logic 0
Logic 1
(low) (0 to 0.8 V)
(high) (2.4 to 4.7 V)
(low) (0 to 0.8 V)
(high) (2.4 to 4.7 V)
Insertion loss
Isolation
Isolation
Insertion loss
Non-inverting
SP1T Control Input Signal Path
E1
J1 – J2
Low
l. loss
High
Isolation
Inverting
Control Input Signal Path
E1
J1 – J2
Low
Isolation
High
l. loss
SPST OUTLINE DRAWING
"SMA" FEMALE
CONNECTOR,
TYP. (2) PLACES
0.40 [10.16]
0.18
[4.57]
E1
0.80 [20.32]
0.60 [15.25]
J1
+5 V
0.36 [9.14] MAX.
0.10 [2.54] TYP.
0.104 [2.64] DIA. THRU,
4 HOLES TYP.
0.11 [2.79]
TYP.
J2
-12 V
0.38
[9.65]
TYP.
0.40 [10.16]
0.10 [2.54]
0.80 [20.32]
1.00 [25.40]
GND. PIN
0.40
[10.16]
0.11 [2.79]
TYP.
0.50
[12.70]
0.18 [4.57]
0.18 [4.57]
GENERAL NOTES:
1. Dimensions shown in brackets [ ] are in millimeters.
2. Unless specified, all connectors are type SMA female
field replaceable. SMA male also available, see
ordering options.
3. Tolerance as follows:
.xx = ±0.01 [.xx = ±0.25]
.xxx = ±0.005 [.xxx = ±0.13]
100 Davids Drive, Hauppauge, NY 11788 • TEL: (631) 436-7400 • FAX: (631) 436-7430 •
www.miteq.com
SINGLE-POLE ORDERING INFORMATION
SP1T SWITCH SINGLE-THROW SWITCHES
To order a switch, please include the model number derived from the following table. If requesting a quotation for a switch not
listed in this catalog, please consult MITEQ. Include any additional specifications that are not listed.
SW
SWITCH
Number of throw(s)
Frequency (100’s of MHz)
Lower frequency
Upper frequency
1 - 020
180
A
N
1
N
F
Type
Absorptive ............................................................................A
Reflective .............................................................................R
Logic
Non-inverting........................................................................N
Inverting ...............................................................................I
No driver ..............................................................................X (See Note 1)
Power Supply
+5 V, -12 V ...........................................................................1
+5 V, -5 V .............................................................................2 (See Note 2)
+5 V, -15 V ...........................................................................3
+12 V, -12 V .........................................................................4
+15 V, -15 V .........................................................................5
No driver ..............................................................................X
Hermeticity
Non-hermetic .......................................................................
N
Hermetic...............................................................................
H
Connectors
SMA-Female ........................................................................
F
SMA-Male ............................................................................
M
Note 1: For “no driver” option, unit is current controlled through logic control pin, -20 mA for low loss condition and +20 mA for
isolation state. Switching speeds are not measured on driverless units.
Note 2: This option has 0.2 dB higher insertion loss, on/off time is 50 ns maximum and rise/fall time is 30 ns typical.
AVAILABLE OPTIONS
• Add suffix FS .............. Ultra-fast switching (SP1T Reflective only with power supply Option 1)
• Add suffix VL1 ............ Common port video filter
• Add suffix VL2 ............ Output port(s) video filter
• Add suffix VL3 ............ Both common port and output port(s) video filter
• Add suffix HP.............. Higher power (alternate package configurations)
Example:
The above illustrated part number SW1-020180AN1NF is for the following: Switch SP1T
2 to 18 GHz
Absorptive
Non-inverting
+5 V, -12 V
Non-hermetic
SMA-F connectors
Consult MITEQ for additional options.
When additional options are ordered, MITEQ will add a 4 digit number (-SXXXX) suffix to the part number.
100 Davids Drive, Hauppauge, NY 11788 • TEL: (631) 436-7400 • FAX: (631) 436-7430 •
www.miteq.com
京公网安备 11010802033920号
EEWORLD
