EEWORLDEEWORLDEEWORLD

Part Number

Search

9112-3-223-02

Description
Board Connector, 46 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Receptacle
CategoryThe connector    The connector   
File Size177KB,1 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

9112-3-223-02 Overview

Board Connector, 46 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Receptacle

9112-3-223-02 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.22 inch
subject depth0.255 inch
body length2.29 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD OVER NICKEL
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage1500VAC V
maximum insertion force2.78 N
Insulation resistance5000000000 Ω
insulator materialGLASS FILLED POLYCARBONATE
Manufacturer's serial number9100
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.11 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts46
Evacuation force-minimum value.556 N
.100” (2.54mm) Dual Row,
Through Hole, Right Angle Header
9100 SERIES
(“POST/BOXE”)
PART NUMBER LEGEND
91XX-3-2XX-XX
PIN NUMBER
(SEE TABLE 2)
NUMBER OF POSITIONS
(SEE TABLE 1)
PIN PLATING
(SEE NOTE 3)
INSULATOR MATERIAL
(SEE NOTE 1)
MATING CONNECTORS: 9000 SERIES
Connector Products
1700 Hicks Road • Rolling Meadows, IL 60008 USA
Telephone: 847.392.3500 • Fax: 847.392.9404
email: mcpsales@methode.com • Web Page: www.methode.com
This appears and I can't choose it. It's grayed out.
Help me, this happens when I place a pad. I searched and it said to not select a slot and select a round one, but it is grayed out and I can't select it. What should I do? Thank you!...
chenbingjy PCB Design
【AT-START-F403A Review】3. Try USB Composite_Device
[i=s]This post was last edited by mig29 on 2020-11-6 20:47[/i]This article is mainly used as a memo note: confirm that the USB Composite_Device Demo of Artery is easy to use and has a good program str...
mig29 Domestic Chip Exchange
The difference between RETI and RET in MCU assembly instructions
[size=5]Normally, RET is used for return in ordinary assembly subroutines, and RETI is used for interrupt return in interrupt service subroutines. Both instructions can pop the breakpoint address from...
fish001 Microcontroller MCU
[Sipeed LicheeRV 86 Panel Review] 10. LVGL Timer
Since the porting of lvgl to 86 board has been realized , many cases can be built based on the lvgl framework. In the previous article, I said that I felt that the documentation of lvgl was not well o...
sonicfirr Domestic Chip Exchange
Holtek Microcontroller Development System HT-IDE3000 SP3 Released
Holtek Microcontroller Development System HT-IDE3000 SP3 Released Since its launch, Holtek Microcontroller Development System has provided programmers with the best tools for program development, debu...
fighting MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号