IP Rating ............................................................ IP 40 .....................................................................IP 40
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Mechanical Characteristics
1
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Single or Dual Section (A & R Bushings) .................................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
Weight (Single Section, Metal Bushing)...............................................................................................................................12.7 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers).............................................................................................................................2 cups maximum
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE:
1
At
Performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Model 91, 92, 93, 94 & 95 - 5/8 ” Square Single-Turn Panel Control
Product Dimensions
Model 91 PC Pin Terminals, In-Line
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
L
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
Model 92 J-Hooked
Terminals, In-Line
.79
(.031) 2 PLCS.
3 2 1
.254
(.010)
GAP
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
10.16 ± 0.30
(.400 ± .012)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
15.29 ± 0.56
(.602 ± .022)
5.08
(.20)
1.52
(.06)
R2
R1
1
2
3
1
2
3
2.54
(.100)
2.54
(.100)
Model 94 J-Hooked
Terminals, "L" Pattern
0.76 ± 0.05
(.030 ± .002)
TYP.
Model 93 PC Pin Terminals, "L" Pattern
22.86 ± 0.43
(.900 ± .017)
MOUNTING
SURFACE
L
12.70 ± .229
(.500 ± .009)
0.79 ± .025
(.031 ± .010)
DIA.
13.72 ± 0.38
(.540 ± .015)
1.37 ± 0.08
(.054 ± .003)
2.36 ± 0.08
(.093 ± .003)
15.88
(.625)
7.92
(.312)
3 2 1
1.52
(.06)
GAP
.81
(.032)
R. MAX.
5.33 ± .76
(.21 ± .03)
3.81
(.150)
MAX. TYP.
SEE
HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
DIA.
0.81
TYP.
(.032)
10.16 ± 0.30
(.400 ± .012)
R2
R1
5.08 ± 0.38
(.200 ± .015)
11.05 ± 0.20
(.435 ± .008)
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
1.19
(.047)
“A” STYLE
A.R. LUG
R
9.53
(.375)
12.7 ± 1.02
(.500 ± .040)
Shaft Flat Orientation
2.54
(.100)
2.54
(.100)
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
1
3
2
1
3
2
0.76 ± 0.05
(.030 ± .002)
TYP.
1
CCW
2
POTENTIOMETER
3
Model 95 Solder Lug Terminals, "Triangular" Pattern
In order to ensure the circuit performance, electromagnetic compatibility should be considered when designing the RF circuit PCB. Therefore, the layout principles of components are discussed in detail...
1 Overview
In recent years, mobile communications have been rapidly developed and popularized in my country, and the transmitter and receiver technologies of wireless communications have also develope...
Sometimes, on the monitor screen, there will be several equally spaced vertical lines. The frequency of this interference signal is basically an integer multiple of the line frequency. If you use an o...
MYB-YT507H provides a 40-pin header with a 2.54mm pitch, interface J25. Through the TWI interface,
Use the PCF8575 chip with a 16-bit quasi-bidirectional input/output (I/O) port to expand the general ...
It’s a very good event, thanks to the website staff;I hope the website will hold more similar events in the future to help more electronics enthusiasts.
I received the board after the holiday when I r...
Last year, I switched from hardware to Linux development. At that time, I was working on drivers. When I went out for interviews, everyone said that they were not hiring for driver positions, only app...
According to a new report from DigiTimes, a major upgrade for the upcoming iPhone 12 this year is that it will be equipped with a LiDAR laser sensor (previously used mainly in the automotive in...[Details]
0 Introduction
With the improvement of global environmental protection awareness and the rapid development of energy-saving requirements, especially in industrial motor control, inverters assem...[Details]
Recently, the first 2023 East Lake Advanced Manufacturing Exhibition held in Wuhan, Hubei Province came to a successful conclusion
. As an invited exhibitor, Haimo Robotics brought a f...[Details]
The circuit for checking the triggering ability of thyristors using a megohmmeter and a multimeter is shown in Figure 1. Set the multimeter to the 1mADC position and connect it in series in the ...[Details]
Recently, we learned from relevant channels that Korean parts manufacturer Hyundai Mobis has developed a new AI technology. This new technology will use artificial intelligence data feedback to judge...[Details]
The ARM Assembly Basics tutorial series will progressively cover the following topics: Part 1: Introduction to ARM Assembly Part 2: Data Type Registers Part 3: ARM instruction set Part 4: Memory inst...[Details]
Many process control sensors, such as thermistors and strain bridges, require accurate bias current. By adding a current setting resistor R 1 , the voltage reference circuit IC 1 can form a constan...[Details]
CS8900+s3c2410 Internet disconnection problem and its solution My understanding is that when the system is running the network, it often enables network interruption, causing the network to reset. Fi...[Details]
Judging from the current situation, this technology is still quite practical. Many storage manufacturers, including Seagate, have begun to shift their focus to external hard disk products. You should ...[Details]
The radar scene simulator recently launched by Keysight Technologies has received such high-standard treatment, with press conferences held in 6 locations and will soon be moved to CES. Why is the ...[Details]
A broken three-way catalytic converter will not affect the starting of the car, nor will it affect the normal use of the engine. The three-way catalytic converter is just a honeycomb-shaped filter ...[Details]
Liu Yunhou, President and Deputy Secretary of the Party Committee of State Grid Technical College
State Grid Corporation of China held a special video conference to arrange and deploy the cons...[Details]
----- Using Mixed Signal Oscilloscopes to Debug Embedded Mixed Signal Designs Today’s embedded designs based on microcontrollers (MCUs) and digital signal processors (DSPs) typically have both analog...[Details]
If you want to drive LED, then use about 1K. If you want a brighter brightness, the resistance can be reduced, the minimum should not be less than 200 ohms, otherwise the current is too large; if you ...[Details]
As automotive companies prepare for intelligence (smart driving and continuous OTA), the speed of automotive networks continues to increase, ushering in a new chapter in technological evolution. In...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
