EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GG-07-2231-DA

Description
RES NET,THIN FILM,2.23K OHMS,100WV,.5% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GG-07-2231-DA Overview

RES NET,THIN FILM,2.23K OHMS,100WV,.5% +/-TOL,-25,25PPM TC,0303 CASE

WBA-T0303GG-07-2231-DA Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberWBA
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance2230 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBA
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
I want to ask what this picture is
The ratio of power and time in the WIFI TX test. I don't understand what it means....
lx331lx RF/Wirelessly
[AutoChips AC7801x motor demo board review] + The indispensable analog-to-digital converter (ADC)
[i=s]This post was last edited by Xianjing on 2020-11-13 10:15[/i]Preface: In real life, many of the things we hear and see are analog and continuous. But we need to observe the changes of these pheno...
仙景 Domestic Chip Exchange
[GD32E503 Review] + First Hands-On Experience
I am very fortunate to be a reviewer of GigaDevice's GD32E503V-EVAL development board.Because I am engaged in the design and development of software and hardware for smart home products, I am exposed ...
linyu0395 Domestic Chip Exchange
MSP430F149 minimum system board uses 1602 LCD display sine wave oscilloscope program control
First, let's talk about the structure of MSP430F149. MSP430 series microcontrollers are 16-bit ultra-low power mixed signal processors with precise instruction set (RISC) that Texas Instruments (TI) b...
fish001 Microcontroller MCU
Practical tutorial | How to use Wangyou DFM software for cold plate analysis
In some product designs that use cold plate cooling, sometimes due to negligence, the cold plate does not avoid the mark point, causing trouble in subsequent production.Today I will teach you how to u...
vayo123 PCB Design
How to deal with cross wiring of PCB circuit boards
In double-sided PCB boards, when there are crossovers, the front and back wiring can be used to solve the problem. In the design of single-sided circuit boards, when some lines cannot be connected, ju...
捷配pcb打样快 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号