VCC4 series
1.8, 2.5, 3.3, 5.0 volt CMOS Oscillator
Features
•
CMOS output
•
Output frequencies to 125 MHz
•
Low jitter, Fundamental or 3 OT Crystal
•
Tristate output for board test and debug
•
-10/70 or –40/85°C operating temperature
•
Gold over nickel contact pads
•
Hermetically sealed ceramic SMD package
rd
The VCC4 Crystal Oscillator
•
Product is compliant to RoHS directive
and fully compatible with lead free assembly
Applications
•
SONET/SDH/DWDM
•
Ethernet, Gigabit Ethernet
•
Storage Area Network
•
Digital Video
•
Broadband Access
f
o
Output
Buffer /
Disable
•
Microprocessors/DSP/FPGA
Description
Vectron’s VCC4 Crystal Oscillator (XO) is quartz
stabilized square wave generator with a CMOS
output, operating off either 1.8, 2.5, 3.3 or 5.0
volt supply.
The VCC4 uses fundamental or 3 overtone
crystals for output frequencies >50MHz resulting
in low jitter performance. Also a monolithic IC,
which improves reliability and reduces cost, is
hermitically sealed.
rd
Vectron International 267 Lowell Road, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC4 Data sheet
Performance Characteristics
Table 1. Electrical Performance, 5V option
Parameter
Symbol
Min
Typical
Maximum
Units
Frequency
1
Operating Supply Voltage
Absolute Maximum Supply Voltage
Supply Current, Output Enabled
< 1.50 MHz
1.500 to 20 MHz
20.01 to 50 MHz
50.01 to 75 MHz
Supply Current, Out disabled
Output Logic Levels
2
Output Logic High
2
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
2
Output Rise/Fall Time
< 20.00 MHz
20.01 to 50.00 MHz
50.01 to 75.00 MHz
3
Duty Cycle
(ordering option)
Operating temperature (ordering
option)
4
Stability (ordering
option)
RMS Jitter, 12kHz to 20 MHz
Period Jitter
RMS
Peak to Peak
5
Output Enable/Disable
Output Enabled
Output Disabled
5
Internal Enable Pull-Up resistor
Start-up time
f
O
V
DD
I
DD
1.544
4.5
-0.7
75.000
5.5
7.0
7
10
30
40
30
MHz
V
V
mA
I
DD
V
OH
V
OL
I
OH
I
OL
t
R/
t
F
0.9*V
DD
uA
V
V
mA
mA
ns
0.1*V
DD
16
16
8
5
2
SYM
45/55
-10/70 or -40/85
±25, ±50, ±100
0.5
3.0
21
1
%
°C
ppm
ps
ps
V
4.0
0.8
100
8
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and
specified.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, and shock and vibration (not under operation).
50 and 100ppm options include aging.
5. Output will be enabled if enable/disable is left open.
t
R
t
F
I
DD
4
V
DD
V
OH
50%
V
OL
On Time
Period
+
-
.
1µF
.01µF
I
C
V
C
1
+
-
2
3
15pF
Figure 1. Output Waveform
Figure 2. Typical Output Test Conditions (25±5°
±
C)
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC4 Data sheet
Table 2. Electrical Performance, 3.3V option
Parameter
Symbol
Min
Typical
Maximum
Units
Frequency
1
Operating Supply Voltage
Absolute Maximum Operating Voltage
Supply Current, Output Enabled
< 1.500 MHz
1.5 to 20 MHz
20.01 to 50 MHz
50.01 to 75 MHz
75.01 to 100 MHz
100.01 to 125 MHz
Supply Current, Output disabled
Output Logic Levels
2
Output Logic High
2
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
2
Output Rise/Fall Time
< 20.00 MHz
20.01 to 50.00 MHz
50.01 to 125.00 MHz
3
Duty Cycle
(ordering option)
Operating temperature (ordering
option)
4
Stability (ordering
option)
RMS Jitter, 12kHz to 20 MHz
Period Jitter
RMS
Peak to Peak
5
Output Enable/Disable
Output Enabled
Output Disabled
5
Internal Enable Pull-Up resistor
Start-up time
f
O
V
DD
I
DD
1.544
2.97
-0.5
3.3
125.000
3.63
5.0
5
7
20
30
40
46
30
MHz
V
V
mA
I
DD
V
OH
V
OL
I
OH
I
OL
t
R/
t
F
0.9*V
DD
uA
V
V
mA
mA
ns
0.1*V
DD
8
8
10
6
3
SYM
45/55
-10/70 or –40/85
±25, ±50, ±100
0.5
3.0
21
1
%
°C
ppm
ps
ps
V
2.0
0.5
100
8
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 3 defines these parameters. Figure 4 illustrates the operating conditions under which these parameters are tested and
specified. For Fo>90MHz, rise and fall time is measured 20 to 80%.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, and shock and vibration (not under operation).
50 and 100ppm options include aging.
5. Output will be enabled if enable/disable is left open.
t
R
t
F
I
DD
4
V
DD
V
OH
50%
V
OL
On Time
Period
+
-
.
1µF
.01µF
I
C
V
C
1
+
-
2
3
15pF
Figure 3. Output Waveform
Figure 4. Typical Output Test Conditions (25±5°
±
C)
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC4 Data sheet
Table 3. Electrical Performance, 2.5V option
Parameter
Symbol
Min
Typical
Maximum
Units
Frequency
1
Operating Supply Voltage
Absolute Maximum Voltage
Supply Current, Output Enabled
< 1.5 MHz
1.500 to 20 MHz
20.01 to 50 MHz
50.01 to 75 MHz
75.01 to 100 MHz
100.01 to 125 MHz
Supply Current, Out disabled
Output Logic Levels
2
Output Logic High
2
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
3
Output Logic High Drive
3
Output Logic Low Drive
2
Output Rise/Fall Time
< 20.000 MHz
20.01 to 50.00 MHz
50.01 to 125.00 MHz
4
Duty Cycle
(ordering option)
Operating temperature (ordering
option)
5
Stability (ordering
option)
RMS Jitter, 12kHz to 20 MHz
Period Jitter
RMS
Peak to Peak
6
Output Enable/Disable
Output Enabled
Output Disabled
6
Internal Enable Pull-Up resistor
Start-up time
f
O
V
DD
I
DD
1.544
2.25
-0.5
2.5
125.000
2.75
5.0
5.0
7.0
15.0
20.0
26.0
36.0
30
MHz
V
V
mA
I
DD
V
OH
V
OL
I
OH
I
OL
I
OH
I
OL
t
R/
t
F
0.9*V
DD
uA
V
V
mA
mA
mA
mA
ns
0.1*V
DD
4
4
8
8
10
6
3
SYM
45/55
-10/70 or –40/85
±25, ±50, ±100
0.5
3.0
21
1
%
°C
ppm
ps
ps
V
1.75
0.5
100
8
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 5 defines these parameters. Figure 6 illustrates the operating conditions under which these parameters are tested and
specified.
3. Overtone designs, output frequencies>35MHz.
4. Symmetry is measured defined as On Time/Period.
5. Includes calibration tolerance, operating temperature, supply voltage variations, and shock and vibration (not under operation).
50 and 100ppm options include aging.
6. Output will be enabled if enable/disable is left open.
t
R
t
F
+
-
I
DD
4
V
OH
50%
V
DD
.
1µF
.01µF
I
C
V
C
1
+
-
2
3
15pF
V
OL
On Time
Period
Figure 5. Output Waveform
Figure 6. Typical Output Test Conditions (25±5°
±
C)
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC4 Data sheet
Table 4. Electrical Performance, 1.8V option
Parameter
Symbol
Min
Typical
Maximum
Units
Frequency
1
Operating Supply Voltage
Absolute Maximum Voltage
Supply Current, Output Enabled
< 20 MHz
20.01 to 70 MHz
Supply Current, Out disabled
Output Logic Levels
2
Output Logic High
2
Output Logic Low
Output Logic High Drive
Output Logic Low Drive
3
Output Logic High Drive
3
Output Logic Low Drive
2
Output Rise/Fall Time
< 20.000 MHz
20.01 to 50.00 MHz
50.01 to 70.00 MHz
4
Duty Cycle (ordering
option)
Operating temperature (ordering
option)
5
Stability (ordering
option)
RMS Jitter, 12kHz to 20 MHz
Period Jitter
RMS
Peak to Peak
6
Output Enable/Disable
Output Enabled
Output Disabled
6
Internal Enable Pull-Up resistor
Start-up time
f
O
V
DD
I
DD
I
DD
V
OH
V
OL
I
OH
I
OL
I
OH
I
OL
t
R/
t
F
1.544
1.71
-0.5
1.8
75.000
1.89
3.6
5
15
30
MHz
V
V
mA
uA
V
V
mA
mA
mA
mA
ns
0.9*V
DD
0.1*V
DD
2.8
2.8
8
8
10
6
3
SYM
45/55
-10/70 or –40/85
±25, ±50, ±100
0.5
3.0
21
1
%
°C
ppm
ps
ps
V
1.26
0.5
1
8
Mohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 7 defines these parameters. Figure 8 illustrates the operating conditions under which these parameters are tested and
specified.
3. Overtone designs, output frequencies>50MHz.
4. Symmetry is measured defined as On Time/Period.
5. Includes calibration tolerance, operating temperature, supply voltage variations, and shock and vibration (not under operation).
50 and 100 ppm options include aging.
6. Output will be enabled if enable/disable is left open.
t
R
t
F
I
DD
V
OH
50%
4
V
DD
V
OL
On Time
Period
+
-
.
1µF
.01µF
I
C
V
C
1
+
-
2
3
15pF
Figure 7. Output Waveform
Figure 8. Typical Output Test Conditions (25±5°
±
C)
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
Linux and Android
京公网安备 11010802033920号
EEWORLD
