UDAA31-T3-DB datasheet, PDF - EEWORLD Datasheet

UDAA31-T3-DB: DescriptionD Type Connector, 25 Contact(s), Male, 0.109 inch Pitch, Solder Terminal, #4-40, Receptacle; CategoryThe connector The connector; File Size282KB，4 Pages; ManufacturerFOXCONN; Websitehttp://www.fit-foxconn.com/

Download Datasheet Parametric View All

UDAA31-T3-DB Overview

D Type Connector, 25 Contact(s), Male, 0.109 inch Pitch, Solder Terminal, #4-40, Receptacle

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	CERAMIC CAPACITIVE FILTER
body width	0.494 inch
subject depth	0.462 inch
body length	2.083 inch
Body/casing type	RECEPTACLE
Contact to complete cooperation	AU
Contact completed and terminated	GOLD
Contact point gender	MALE
Contact material	COPPER ALLOY
contact mode	STAGGERED
Contact resistance	10 mΩ
Contact style	RND PIN-SKT
Dielectric withstand voltage	100VDC V
Filter function	YES
maximum insertion force	3.336 N
Insulation resistance	5000000000 Ω
insulator material	GLASS FILLED POLYESTER
Manufacturer's serial number	UD
Plug contact pitch	0.109 inch
Match contact row spacing	0.112 inch
Installation option 1	#4-40
Installation option 2	CLINCH NUT
Installation method	STRAIGHT
Installation type	BOARD
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	105 °C
Minimum operating temperature	-55 °C
PCB contact pattern	STAGGERED
PCB contact row spacing	2.8448 mm
Plating thickness	FLASH inch
Rated current (signal)	5 A
Guideline	UL
reliability	COMMERCIAL
Shell material	STEEL
Terminal length	0.125 inch
Terminal pitch	2.7686 mm
Termination type	SOLDER
Total number of contacts	25
Evacuation force-minimum value	.2224 N

RT-Thread has been ported to W600: The IoT operating system RT-Thread has been ported to the W600 system, and you can run mpy on the W600.[size=14px][url=http://docs.thingsturn.com/development/rt-thread/start/]W600 RT-Thread (trial ver...; dcexpert MicroPython Open Source section

MakeCode now supports STM103: MakeCode now supports STM103, which is for the bluepill low-cost development board using the STM32F103C8....; dcexpert MicroPython Open Source section

Please help me with the trip zone configuration of TI's 28034!!!: I am a newbie, please help me analyze the reason! !Regarding the configuration of trip zone, when TZ time is triggered, all three PWMs are set to low. After initializing the three PWMs, it is found th...; 源菜鸟 DSP and ARM Processors

Is the threshold for electromagnetic wave and antenna major getting lower and lower? Is the reliance on simulation software getting higher and higher?: When I first entered university, I was told that the electromagnetic field major required a high level of math skills, but later I found that except for computational electromagnetics and a few profes...; btty038 RF/Wirelessly

EV-HC32F460_1. Unboxing: [i=s]This post was last edited by gao_hex on 2021-3-24 09:37[/i]EV-HC32F460 UnboxingDevelopment Data Preparation Introduction Before I start, let me briefly introduce this MCU (HC32F460) from Huada Se...; gao_hex Domestic Chip Exchange

The input capture of stm8s cannot enter the interrupt. Please help? ? Thank you!!!: void TIM1_Init(void){TIM1_IER = 0x00; //Disable interruptsTIM1_EGR = 0x01; //Allow update flag to be generated//TIM1_PSCR = 0x08; //Set clock division 2M/2=1MHz---1usTIM1_PSCRH = 0x00;TIM1_PSCRL = 0x0...; liuxingyuxyz stm32/stm8

Popular Components