REVISION T
DO NOT
SCALE FROM
THIS PRINT
01
07
ROW OPTION
-D: DOUBLE
-S: SINGLE (SEE SHT 3, FIG 4)
C
FEP CABLE OPTION
-T: FEP
(NO OF POS X.100 [2.54])
(LEAVE BLANK FOR
+.070 [1.78] REF
06
STANDARD PVC INSULATION)
(SEE NOTE 11)
No OF POSITIONS
-02 THRU -25 (PER ROW)
.300 7.62 REF C
WIRE GAUGE (AWG)
-20, -22, -24, -26, -28, -30
FEP: -20, -24, -28, -30
12
'C'
COLOR CODE
-C (SEE TABLE 2)
(LEAVE BLANK FOR
STANDARD BLACK CABLE)
(NOT AVAILABLE WITH PTFE OPTION)
"A"
IPM1-XX-D
PLATING SPECIFICATION
-F: 3µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-L: 10µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
C
MATTE TIN ON TAIL
.690 17.53 REF
MMTXX-XX-XX-X-X-XX.XX-X-X-XXX
DOUBLE END OPTIONS
[MUST BE USED ON -D END OPTION ONLY
& APPLIES TO END 2 HOUSING]
-TUS: TRANSFER LATCH UP, STRAIGHT
(SEE FIG 2, SHEET 2)
-TDS: TRANSFER LATCH DOWN, STRAIGHT
(SEE FIG 3, SHEET 2)
-LDS: PLASTIC LATCH DOWN, STRAIGHT
(SEE FIG 9, SHEET 4)
-LUS: PLASTIC LATCH UP, STRAIGHT
(SEE FIG 10, SHEET 4)
*-TDX: TRANSFER LATCH DOWN, CROSSED
(SEE FIG 11, SHEET 5)
*-LDX: PLASTIC LATCH DOWN, CROSSED
(SEE FIG 12, SHEET 5)
POLARIZATION OPTION
-G: GUIDE POST (USE IPM1-XX-D-GP)
(LEAVE BLANK FOR NO POLARIZATION)
(SEE FIG 5 SHEET 3)
(ONLY AVAILABLE ON DOUBLE ROW)
END OPTION
-S: SINGLE END
-D: DOUBLE END(MUST CHOOSE A DOUBLE END OPTION.)
ASSEMBLED LENGTH
SPECIFY IN INCHES [USE DWCX-XX-XX]
(SINGLE END: 03.00[76.2] INCH MINIMUM,
DOUBLE END: 03.25[82.6] INCH MINIMUM)
"A"
C
.020 0.51
REF
.035 0.89 REF
* = 10 POS MAXIMUM, -07.00 MINIMUM
'B'
.035 0.89 REF
DWCX-XX-XX
DETAIL 'C'
SCALE 6 : 1
.004 0.10 REF
(SEE NOTE 5)
NOTES:
FIG 1
DETAIL 'B'
SECTION "A"-"A"
1.
C
REPRESENTS A CRITICAL DIMENSION.
MMTD-06-20-X-X-XX.XX-S SHOWN
SCALE 8 : 1
SCALE 3 : 1
2. NOTE DELETED
3. NOTE DELETED
4. MINIMUM PULLOUT FORCE: 0.5 lbs [2.22 N].
C
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
5. CONTACT MUST BE INSERTED UNTIL RETENTION FEATURE LOCKS
DIMENSIONS ARE IN INCHES.
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
INTO PLACE.
TOLERANCES ARE:
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
C
6. ALL FINISHED GOODS ARE TO BE ELECTRICAL TESTED INCLUDING
DECIMALS
ANGLES
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
HI-POT TEST @ 1000 VOLTS DC. AFTER FINAL ELECTRICAL TEST, LABEL
.XX: .01 [.3]
2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PURPOSE OTHER THAN THAT WHICH IT WAS
.XXX: .005 [.13]
EACH ASSEMBLY WITH (1) ET STAMP ON THE BODY.
PHONE: 812-944-6733
FAX: 812-948-5047
OBTAINED WITHOUT THE EXPRESSED WRITTEN
.XXXX: .0020 [.051]
CONSENT OF SAMTEC, INC.
e-Mail: info@SAMTEC.com
code: 55322
7. TINNED COPPER WIRE IS ROHS COMPLIANT.
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
8. PARTS ARE TO BE LAYER PACKAGED.
.100[2.54] TERMINAL DISCRETE CABLE ASSEMBLY
9. REFER TO CRIMP SPECIFICATIONS PRINT FOR CRIMP AND STRIP DIMENSIONS,
HOUSING: NYLON 6/6, COLOR: WHITE
CONTACT: PHOS BRONZE
TOLERANCES, TOOLING AND ITS REQUIREMENTS.
DWG. NO.
CABLE: INSULATION: SEE CALLOUT
10. FOR LENGTHS LESS THAN 12 IN[304.8], TOLERANCE SHALL BE ±.125[3.18].
WIRE: TINNED COPPER
MMTXX-XX-XX-X-X-XX.XX-X-X-XXX
FOR OTHER LENGTHS, TOLERANCES SHALL BE ± 2%.
11. ASSEMBLIES USING THE FEP OPTION ARE FOR CRIMP APPLICATIONS ONLY.
BY:
D. SCHMELZ 12/04/2008
SHEET
1
OF
5
F:\DWG\MISC\MKTG\MMTXX-XX-XX-X-X-XX.XX-X-X-XXX-MKT.SLDDRW
REVISION T
N/2
N
C
XX.XX
(SEE NOTE 10)
IPD1-XX-X-K-M
N
N/2
N/2
N
01
N/2+1
01
N/2+1
.620 15.74
REF
N/2+1
01
01
N/2+1
N/2
N
END 1
END 2
END 1
END 2
(TRANSFER,LATCH UP, STRAIGHT)
(SAME AS FIG1 UNLESS OTHERWISE STATED)
(SEE SHEET 3, TABLE 4 FOR PIN MAPPING)
FIG 2
-TUS
(TRANSFER,LATCH DOWN, STRAIGHT)
(SAME AS FIG 2, UNLESS OTHERWISE STATED)
(SEE SHEET 3, TABLE 4 FOR PIN MAPPING)
FIG 3
-TDS
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.100[2.54] TERMINAL DISCRETE CABLE ASSEMBLY
MMTXX-XX-XX-X-X-XX.XX-X-X-XXX
F:\DWG\MISC\MKTG\MMTXX-XX-XX-X-X-XX.XX-X-X-XXX-MKT.SLDDRW
BY:
D. SCHMELZ 12/04/2008
SHEET
2
OF
5
REVISION T
01
01 02
.200 5.08 REF
07
12
.090 2.28 REF
IPM1-XX-S
.110 2.79 REF
06
IPM1-XX-D-GP
MMTD-06-20-X-X-XX.XX-G-S SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 5
IPM1-XX-D-GP
N/2
N
LTC-14-01-N
IPD1-XX-X-GP-R
N
N/2
01
N/2+1
N/2+1
01
MMTD-06-20-X-X-XX.XX-G-TUS SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
(SEE TABLE 4 FOR PIN MAPPING)
MMTS-06-20-X-XX.XX-S SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 6
FIG 4
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.100[2.54] TERMINAL DISCRETE CABLE ASSEMBLY
F:\DWG\MISC\MKTG\MMTXX-XX-XX-X-X-XX.XX-X-X-XXX-MKT.SLDDRW
BY:
D. SCHMELZ 12/04/2008
SHEET
3
OF
5
MMTXX-XX-XX-X-X-XX.XX-X-X-XXX
REVISION T
IPD1-XX-D-XX-X
N/2
N
.250 6.35 REF
01
.100 2.54 REF
N/2 + 1
C
(No OF POS x .100[2.54]
+ .055[1.40]) REF
01
N/2+1
C
.505 12.83 REF
.285 7.24 REF
N/2
N
.353 8.97 REF
C
END 1
(TRANSFER,LATCH DOWN, STRAIGHT)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2)
(SEE SHEET 3, TABLE 4 FOR PIN MAPPING)
FIG 9
-LDS
LATCH-
END 2
N/2
N
N
N/2
01
N/2+1
N/2 + 1
01
END 1
LATCH-
END 2
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
(TRANSFER,LATCH UP, STRAIGHT)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2 & 9)
(SEE SHEET 3, TABLE 4 FOR PIN MAPPING)
FIG 10
-LUS
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.100[2.54] TERMINAL DISCRETE CABLE ASSEMBLY
F:\DWG\MISC\MKTG\MMTXX-XX-XX-X-X-XX.XX-X-X-XXX-MKT.SLDDRW
BY:
D. SCHMELZ12/04/2008
MMTXX-XX-XX-X-X-XX.XX-X-X-XXX
SHEET
4
OF
5
REVISION T
N/2
N
01
N/2+1
01
N/2+1
N/2
N
END 1
END 2
LATCH DOWN
(TRANSFER,LATCH DOWN, CROSSED)
(SAME AS FIG 2, UNLESS OTHERWISE STATED)
(SEE SHEET 3, TABLE 4 FOR PIN MAPPING)
FIG 12
-TDX
N/2
N
01
N/2+1
01
N/2+1
N/2
N
END 1
END 2
LATCH DOWN
(TRANSFER,LATCH DOWN, CROSSED)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2)
(SEE SHEET 3, TABLE 4 FOR PIN MAPPING)
FIG 14
-LDX
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.100[2.54] TERMINAL DISCRETE CABLE ASSEMBLY
MMTXX-XX-XX-X-X-XX.XX-X-X-XXX
12/04/2008
SHEET
5
OF
5
F:\DWG\MISC\MKTG\MMTXX-XX-XX-X-X-XX.XX-X-X-XXX-MKT.SLDDRW
BY:
D. SCHMELZ
京公网安备 11010802033920号
EEWORLD
