EEWORLDEEWORLDEEWORLD

Part Number

Search

LT1376IN8

Description
Conv DC-DC 5V to 25V Synchronous Step Down Single-Out 2.42V to 20.64V 1.5A 8-Pin PDIP N
CategoryPower/power management    The power supply circuit   
File Size482KB,28 Pages
ManufacturerADI
Websitehttps://www.analog.com
Download Datasheet Parametric View All

LT1376IN8 Overview

Conv DC-DC 5V to 25V Synchronous Step Down Single-Out 2.42V to 20.64V 1.5A 8-Pin PDIP N

LT1376IN8 Parametric

Parameter NameAttribute value
EU restricts the use of certain hazardous substancesNot Compliant
ECCN (US)EAR99
Part StatusUnconfirmed
HTS8542.39.00.01
SVHCYes
SVHC Exceeds ThresholdYes
TypeSynchronous Step Down
Output TypeAdjustable
Switching Frequency (kHz)560
Switching RegulatorYes
Number of Outputs1
Output Voltage (V)2.42 to 20.64
Maximum Output Current (A)1.5
Minimum Input Voltage (V)5
Maximum Input Voltage (V)25
Operating Supply Voltage (V)5 to 25
Typical Switch Current (A)2
Minimum Operating Temperature (°C)-40
Maximum Operating Temperature (°C)125
Supplier Temperature GradeIndustrial
Pin Count8
Standard Package NameDIP
Supplier PackagePDIP N
MountingThrough Hole
Package Height3.3
Package Length10.16(Max)
Package Width6.48
PCB changed8
Lead ShapeThrough Hole
LT1375/LT1376
1.5A, 500kHz Step-Down
Switching Regulators
FEATURES
Constant 500kHz Switching Frequency
Uses All Surface Mount Components
Inductor Size Reduced to 5
µ
H
Easily Synchronizable
Saturating Switch Design: 0.4Ω
Effective Supply Current: 2.5mA
Shutdown Current: 20µA
Cycle-by-Cycle Current Limiting
is current mode for fast transient response and good loop
stability. Both fixed output voltage and adjustable parts are
available.
A special high speed bipolar process and new design
techniques achieve high efficiency at high switching fre-
quency. Efficiency is maintained over a wide output cur-
rent range by using the output to bias the circuitry and by
utilizing a supply boost capacitor to saturate the power
switch. A shutdown signal will reduce supply current to
20µA on both parts. The LT1375 can be externally syn-
chronized from 580kHz to 900kHz with logic level inputs.
The LT1375/LT1376 fit into standard 8-pin PDIP and SO
packages, as well as a fused lead 16-pin SO with much
lower thermal resistance. Full cycle-by-cycle short-cir-
cuit protection and thermal shutdown are provided.
Standard surface mount external parts are used, includ-
ing the inductor and capacitors.
For low input voltage applications with 3.3V output, see
LT1507. This is a functionally identical part that can
operate with input voltages between 4.5V and 12V.
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
APPLICATIO S
Portable Computers
Battery-Powered Systems
Battery Charger
Distributed Power
DESCRIPTIO
The LT
®
1375/LT1376 are 500kHz monolithic buck mode
switching regulators. A 1.5A switch is included on the die
along with all the necessary oscillator, control and logic
circuitry. High switching frequency allows a considerable
reduction in the size of external components. The topology
TYPICAL APPLICATIO
5V Buck Converter
D2
1N914
C2
0.1µF
V
SW
LT1376-5 BIAS
L1**
5µH
6V
TO 25V
C3*
10µF TO
50µF
+
DEFAULT
= ON
V
IN
EFFICIENCY (%)
INPUT
BOOST
SHDN
GND
* RIPPLE CURRENT
I
OUT
/2
** INCREASE L1 TO 10µH FOR LOAD CURRENTS ABOVE 0.6A AND TO 20µH ABOVE 1A
FOR INPUT VOLTAGE BELOW 7.5V, SOME RESTRICTIONS MAY APPLY.
SEE APPLICATIONS INFORMATION.
U
U
U
Efficiency vs Load Current
100
V
OUT
= 5V
V
IN
= 10V
L = 10µH
90
OUTPUT**
5V, 1.25A
80
FB
V
C
C
C
3.3nF
D2
1N5818
+
C1
100µF, 10V
SOLID
TANTALUM
70
60
50
0
1375/76 TA01
0.25
0.75
1.00
0.50
LOAD CURRENT (A)
1.25
1375/76 TA02
13756fd
1
How to use trap and varbind in lwip2.1.2
Previously, I used lwip1.4.1, which had the concept of varbindlist. Each varbind to be sent was combined into a list, and then a trap was sent. Now I am using lwip2.1.2, which does not have the concep...
李嘟嘟他爸 stm32/stm8
str91 p6.6 p6.7 port always freezes when configuring uart0
stopped external ....by other core It always fails to execute. When I disable GPIO_IPINPUTConneced of pin 6.6, I can send content. But I can't receive. The similar program has been implemented on UART...
sebrina2010 stm32/stm8
CAN source code dual channel
[i=s] This post was last edited by peiweihua on 2019-4-12 06:01 [/i] {:1_138:} CAN line source code, which contains pure CAN line...
peiweihua MCU
Effects of ESR and ESL in Decoupling Applications
Continued from the previous article~~~~~ Continue the decoupling/bypass journey~~~~~~~· This article explains in detail the effects of ESR and ESL on decoupling through examples. By comparing theoreti...
nathanzhang Analog electronics
The new computer I bought can't be turned on, please help
My new computer arrived today. When I bought it, there were 512+1T hard drives and 512 only hard drives. Since I have a lot of hard drives and I plan to install them myself, I didn't choose the one wi...
littleshrimp Integrated technical exchanges
Solution to the failure of IAR programming MSP430
1. The failure conditions are as follows:The driver installation is correct (the board is automatically installed after the USB is plugged in): If the MCU selected in config is correct, an error will ...
灞波儿奔 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号