EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

7107LDZQE22

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-OFF-(ON),SOLDER TERMINAL,TOGGLE
CategoryMechanical and electronic products    switch   
File Size1MB,14 Pages
ManufacturerC&K Components
Environmental Compliance
Download Datasheet Parametric View All

7107LDZQE22 Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-OFF-(ON),SOLDER TERMINAL,TOGGLE

7107LDZQE22 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerC&K Components
Reach Compliance Codenot_compliant
ECCN codeEAR99
Actuator angle25 deg
Actuator colorBLACK
Actuator length0.84 inch
Actuator materialBRASS
Actuator typeTOGGLE
body width6.858 mm
body height8.89 mm
Body length or diameter12.7 mm
Nozzle length0.35 inch
Casing type1/4-40
center contact materialCOPPER ALLOY
Center contact platingSILVER
Contact (AC) maximum rated R load2A@250VAC
Maximum contact current (AC)2 A
Maximum contact current (DC)5 A
Contact (DC) maximum rated R load5A@28VDC
Contact functionON-OFF-(ON)
Contact resistance0.01 mΩ
Maximum contact voltage (AC)250 V
Maximum contact voltage (DC)28 V
Dielectric withstand voltage1400VAC V
Electrical life100000 Cycle(s)
End contact materialCOIN SILVER
End contact platingSILVER
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
Manufacturer's serial number7000
Installation featuresPANEL MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
sealEPOXY
surface mountNO
Switch actionMOMENTARY
switch functionSPDT
Switch typeTOGGLE SWITCH
Terminal surfaceTIN/NICKEL
Terminal materialCOPPER ALLOY
Termination typeSOLDER LUG
I'm a newbie and need help. How to declare lcd_wdat? Please help me.
I am a newbie with a poor foundation in MCU C language. I saw a compilation error in a case program in a book. If I am not wrong, is it a declaration problem? So how should lcd_wdat be declared, what ...
落魄IV MCU
Experience in Application Test of DSP External SRAM
Figure 1-1 Code Composer Studio 6.0.0.00190 C/C++ development environment The hardware platform is based on the TMS320F28335 chip, and the software platform is based on TI's Code Composer Studio 6.0.0...
fish001 Microcontroller MCU
【TI mmWave Radar Evaluation】+Configuration File Test (Part 2)
Continuing from the previous post: adcbufCfg 0 1 0 1 //ADC cache configuration The document describes that the first parameter configuration is 0, does not support IWR144, only supports 16, the second...
29447945 TI Technology Forum
[AT-START-F425 Review] + Get MCU 96-bit unique ID, FLASH size
1. About electronic signature The electronic signature of the device contains storage capacity information and a 96-bit unique device ID. It is stored in the information module of the on-chip flash me...
freeelectron Domestic Chip Exchange
Looking for a car charger IC with dual port output power of 40W or more C+A port
Looking for a car charger IC with dual-port output power of more than 40W. The C+A port requires various charging protocols, at least PD protocol, and can support MAC BOOK charging. Please recommend i...
fangfang120 Power technology
Why does the ripple of a switching power supply increase as the output voltage decreases?
[i=s]This post was last edited by sfcsdc on 2020-4-20 16:35[/i]Previously I asked you how a switching power supply can output a voltage lower than the reference voltage. https://en.eeworld.com/bbs/thr...
sfcsdc Analog electronics

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号